ATmega8515 Atmel Corporation, ATmega8515 Datasheet - Page 56

• Manufacturer Part Number: ATmega8515
• Manufacturer: Atmel Corporation

Specifications of ATmega8515

• Flash (kbytes): 8 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 35
• Ext Interrupts: 3
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 3
• Input Capture Channels: 1
• Pwm Channels: 3
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

56
ATmega8515(L)
When the BOOTRST Fuse is unprogrammed, the Boot section size set to 2K bytes and
the IVSEL bit in the GICR Register is set before any interrupts are enabled, the most
typical and general program setup for the Reset and Interrupt Vector Addresses is:
When the BOOTRST Fuse is programmed and the Boot section size set to 2K bytes, the
most typical and general program setup for the Reset and Interrupt Vector Addresses is:
When the BOOTRST Fuse is programmed, the Boot section size set to 2K bytes and the
IVSEL bit in the GICR Register is set before any interrupts are enabled, the most typical
and general program setup for the Reset and Interrupt Vector Addresses is:
Address Labels
$000
$001
$002
$003
$004
$005
;
.org $C02
$C02
$C04
...
$C2A
Handler
Address Labels
.org $002
$001
$002
...
$010
Handler
;
.org $C00
$C00
$C01
$C02
$C03
$C04
$C05
Address Labels
.org $C00
$C00
$C01
$C02
...
$C10
Handler
;
$C11
RESET:
....
....
RESET:
....
RESET:
Code
ldi
out
ldi
out
sei
<instr>
rjmp EXT_INT0
rjmp EXT_INT1
..
rjmp SPM_RDY
Code
rjmp EXT_INT0
rjmp EXT_INT1
..
rjmp SPM_RDY
ldi
out
ldi
out
sei
<instr>
Code
rjmp RESET
rjmp EXT_INT0
rjmp EXT_INT1
..
rjmp SPM_RDY
ldi
r16,high(RAMEND); Main program start
SPH,r16
r16,low(RAMEND)
SPL,r16
r16,high(RAMEND); Main program start
SPH,r16
r16,low(RAMEND)
SPL,r16
r16,high(RAMEND); Main program start
xxx
xxx
; Set Stack Pointer to top of RAM
; Enable interrupts
; IRQ0 Handler
; IRQ1 Handler
;
; Store Program memory Ready
Comments
; IRQ0 Handler
; IRQ1 Handler
;
; Store Program memory Ready
; Set Stack Pointer to top of RAM
; Enable interrupts
; Reset handler
; IRQ0 Handler
; IRQ1 Handler
;
; Store Program memory Ready
Comments
Comments
2512K–AVR–01/10