ATmega88PA Atmel Corporation, ATmega88PA Datasheet - Page 272

no-image

ATmega88PA

Manufacturer Part Number
ATmega88PA
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of ATmega88PA

Flash (kbytes)
8 Kbytes
Pin Count
32
Max. Operating Frequency
20 MHz
Cpu
8-bit AVR
# Of Touch Channels
12
Hardware Qtouch Acquisition
No
Max I/o Pins
23
Ext Interrupts
24
Usb Speed
No
Usb Interface
No
Spi
2
Twi (i2c)
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
1
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8 to 5.5
Operating Voltage (vcc)
1.8 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
6
Input Capture Channels
1
Pwm Channels
6
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATmega88PA-15AZ
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega88PA-15MZ
Manufacturer:
ATMEL
Quantity:
228
Part Number:
ATmega88PA-AN
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega88PA-ANR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega88PA-AU
Manufacturer:
ATMEL
Quantity:
14 000
Part Number:
ATmega88PA-AU
Manufacturer:
Atmel
Quantity:
64
Part Number:
ATmega88PA-AU
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega88PA-AU
Manufacturer:
ATMEL
Quantity:
755
Part Number:
ATmega88PA-AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega88PA-MMH
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega88PA-MMHR
Manufacturer:
MTK
Quantity:
101
Part Number:
ATmega88PA-MMHR
Manufacturer:
ATMEL
Quantity:
20 000
Company:
Part Number:
ATmega88PA-MMHR
Quantity:
6 000
Part Number:
ATmega88PA-MU
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
ATmega88PA-MU
Manufacturer:
MICROCHIP/微芯
Quantity:
135
Part Number:
ATmega88PA-PU
Manufacturer:
MICREL
Quantity:
2 001
26.1.3
26.2
8271D–AVR–05/11
Addressing the Flash During Self-Programming
Performing a Page Write
SPMCSR. It is also erased after a system reset. Note that it is not possible to write more than
one time to each address without erasing the temporary buffer.
If the EEPROM is written in the middle of an SPM Page Load operation, all data loaded will be
lost.
To execute Page Write, set up the address in the Z-pointer, write “00000101” to SPMCSR and
execute SPM within four clock cycles after writing SPMCSR. The data in R1 and R0 is ignored.
The page address must be written to PCPAGE. Other bits in the Z-pointer must be written to
zero during this operation.
• The CPU is halted during the Page Write operation.
The Z-pointer is used to address the SPM commands.
Since the Flash is organized in pages (see
be treated as having two different sections. One section, consisting of the least significant bits, is
addressing the words within a page, while the most significant bits are addressing the pages.
This is shown in
are addressed independently. Therefore it is of major importance that the software addresses
the same page in both the Page Erase and Page Write operation.
The LPM instruction uses the Z-pointer to store the address. Since this instruction addresses the
Flash byte-by-byte, also the LSB (bit Z0) of the Z-pointer is used.
Bit
ZH (R31)
ZL (R30)
Figure 27-3 on page
Z15
15
Z7
7
ATmega48A/PA/88A/PA/168A/PA/328/P
Z14
14
Z6
6
Z13
13
Z5
5
285. Note that the Page Erase and Page Write operations
Table 28-11 on page
Z12
12
Z4
4
Z11
11
Z3
3
Z10
10
Z2
2
302), the Program Counter can
Z9
Z1
9
1
Z8
Z0
8
0
272

Related parts for ATmega88PA