ATmega88PA Atmel Corporation, ATmega88PA Datasheet - Page 64

• Manufacturer Part Number: ATmega88PA
• Manufacturer: Atmel Corporation

Specifications of ATmega88PA

• Flash (kbytes): 8 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 23
• Ext Interrupts: 24
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

12.3
Table 12-4.
Notes:
8271D–AVR–05/11
VectorNo.
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
1
2
3
4
5
6
7
8
9
Interrupt Vectors in ATmega168A and ATmega168PA
1. When the BOOTRST Fuse is programmed, the device will jump to the Boot Loader address at reset, see
2. When the IVSEL bit in MCUCR is set, Interrupt Vectors will be moved to the start of the Boot Flash Section. The address of
port – Read-While-Write Self-Programming” on page
each Interrupt Vector will then be the address in this table added to the start address of the Boot Flash Section.
Reset and Interrupt Vectors in ATmega168A and ATmega168PA
Address
0x0000
Program
0x000A
0x000C
0x000E
0x001A
0x001C
0x001E
0x002A
0x002C
0x002E
0x0002
0x0004
0x0006
0x0008
0x0010
0x0012
0x0014
0x0016
0x0018
0x0020
0x0022
0x0024
0x0026
0x0028
0x0030
0x0032
(1)
(2)
0xC1B
0xC1C
0xC1D
0xC1E
0xC1F
Source
RESET
INT0
INT1
PCINT0
PCINT1
PCINT2
WDT
TIMER2 COMPA
TIMER2 COMPB
TIMER2 OVF
TIMER1 CAPT
TIMER1 COMPA
TIMER1 COMPB
TIMER1 OVF
TIMER0 COMPA
TIMER0 COMPB
TIMER0 OVF
SPI, STC
USART, RX
USART, UDRE
USART, TX
ADC
EE READY
ANALOG COMP
TWI
SPM READY
ATmega48A/PA/88A/PA/168A/PA/328/P
out
ldi
out
sei
<instr>
Interrupt Definition
External Pin, Power-on Reset, Brown-out Reset and Watchdog System Reset
External Interrupt Request 0
External Interrupt Request 1
Pin Change Interrupt Request 0
Pin Change Interrupt Request 1
Pin Change Interrupt Request 2
Watchdog Time-out Interrupt
Timer/Counter2 Compare Match A
Timer/Counter2 Compare Match B
Timer/Counter2 Overflow
Timer/Counter1 Capture Event
Timer/Counter1 Compare Match A
Timer/Coutner1 Compare Match B
Timer/Counter1 Overflow
Timer/Counter0 Compare Match A
Timer/Counter0 Compare Match B
Timer/Counter0 Overflow
SPI Serial Transfer Complete
USART Rx Complete
USART, Data Register Empty
USART, Tx Complete
ADC Conversion Complete
EEPROM Ready
Analog Comparator
2-wire Serial Interface
Store Program Memory Ready
SPH,r16
r16,low(RAMEND)
SPL,r16
280.
xxx
; Set Stack Pointer to top of RAM
; Enable interrupts
”Boot Loader Sup-
64