ATtiny10 Atmel Corporation, ATtiny10 Datasheet - Page 3

• Manufacturer Part Number: ATtiny10
• Manufacturer: Atmel Corporation

Specifications of ATtiny10

• Flash (kbytes): 1 Kbytes
• Pin Count: 6
• Max. Operating Frequency: 12 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 1
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 4
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 4
• Adc Resolution (bits): 8
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.03
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 125
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 1
• Output Compare Channels: 2
• Input Capture Channels: 1
• Pwm Channels: 2
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

Table 1-1.
Notes:
1.3
8127D–Appendix A–AVR–08/11
Symbol
I
CC
1. “Min” means the lowest value where the pin is guaranteed to be read as high.
2. “Max” means the highest value where the pin is guaranteed to be read as low.
3. Although each I/O port can sink more than the test conditions (10 mA at V
4. Although each I/O port can source more than the test conditions (10 mA at V
5. The RESET pin must tolerate high voltages when entering and operating in programming modes and, as a consequence,
6. Values are with external clock. Power Reduction is enabled (PRR = 0xFF) and there is no I/O drive.
7. BOD Disabled.
Speed
conditions (non-transient), the sum of all I
may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test condition.
conditions (non-transient), the sum of all I
may exceed the related specification. Pins are not guaranteed to source current greater than the listed test condition.
has a weak drive strength as compared to regular I/O pins.
Parameter
Power Supply Current
Power-down mode
DC Characteristics. T
The maximum operating frequency of the device depends on V
relationship between maximum frequency vs. V
Figure 1-1.
(7)
(6)
A
Active 4MHz, V
Active 8MHz, V
Idle 1MHz, V
WDT disabled, V
Condition
Active 1MHz, V
Idle 4MHz, V
Idle 8MHz, V
WDT enabled, V
= -40°C to +125°C (Continued)
10 MHz
6 MHz
4 MHz
Maximum Frequency vs. V
1.8V
OL
OH
CC
CC
CC
(for all ports) should not exceed 60 mA. If I
(for all ports) should not exceed 60 mA. If I
CC
CC
CC
= 2V
= 3V
= 5V
CC
CC
= 2V
= 3V
= 5V
= 3V
= 3V
2.7V
CC
Min.
CC
is linear between 1.8V < V
4.5V
CC
CC
= 5V, 5 mA at V
= 5V, 5 mA at V
Typ.
0.02
0.13
0.15
0.2
0.8
2.7
0.6
4.5
OL
OH
CC
exceeds the test conditions, V
exceeds the test condition, V
. As shown in
CC
5.5V
ATtiny4/5/9/10
CC
= 3V) under steady state
Max.
0.5
1.5
0.2
0.5
1.5
20
10
5
= 3V) under steady state
CC
< 4.5V.
Figure
Units
mA
mA
mA
mA
mA
mA
µA
µA
1-1, the
OH
OL
3