ATtiny13 Atmel Corporation, ATtiny13 Datasheet - Page 115

• Manufacturer Part Number: ATtiny13
• Manufacturer: Atmel Corporation

Specifications of ATtiny13

• Flash (kbytes): 1 Kbytes
• Pin Count: 8
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 6
• Ext Interrupts: 6
• Usb Speed: No
• Usb Interface: No
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 4
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.06
• Eeprom (bytes): 64
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 1
• Output Compare Channels: 2
• Pwm Channels: 2
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

17.8.7
17.8.8
18. Electrical Characteristics
18.1
18.2
Table 18-1.
2535J–AVR–08/10
Operating Temperature.................................. -55°C to +125°C
Storage Temperature ..................................... -65°C to +150°C
Voltage on any Pin except RESET
with respect to Ground ................................-0.5V to V
Voltage on RESET with respect to Ground......-0.5V to +13.0V
Maximum Operating Voltage ............................................ 6.0V
DC Current per I/O Pin ............................................... 40.0 mA
DC Current V
Symbol
V
V
V
V
I
LIL
OH
OL
IH
IL
Absolute Maximum Ratings*
DC Characteristics
Reading the Signature Bytes and Calibration Byte
Power-off sequence
Parameter
Input Low Voltage,
Any Pin as I/O
Input Low Voltage,
RESET Pin as Reset
Input High Voltage,
Any Pin as I/O
Input High Voltage,
RESET Pin as Reset
Output Low Voltage,
Pins PB0 and PB1
Output Low Voltage,
Pins PB2, PB3 and PB4
Output High Voltage,
Pins PB0 and PB1
Output High Voltage,
Pins PB2, PB3 and PB4
Input Leakage
Current I/O Pin
CC
DC Characteristics, T
and GND Pins ................................ 200.0 mA
The algorithms for reading the Signature bytes and Calibration byte are shown in
page
Set SCI to “0”. Set RESET to “1”. Turn V
(5)
(6)
(3)
(3)
110.
(5)
(6)
A
= -40°C to +85°C
Condition
V
V
V
V
V
V
I
I
I
I
I
I
I
I
V
OL
OL
OL
OL
OH
OH
OH
OH
CC
CC
CC
CC
CC
CC
CC
= 20 mA, V
= 10 mA, V
= 10 mA, V
= 5 mA, V
= -20 mA, V
= -10 mA, V
= -10 mA, V
= -5 mA, V
= 1.8V - 2.4V
= 2.4V - 5.5V
= 1.8V - 5.5
= 1.8V - 2.4V
= 2.4V - 5.5V
= 1.8V - 5.5V
= 5.5V, pin low
CC
CC
+0.5V
CC
CC
CC
CC
CC
CC
CC
= 3V
= 3V
= 5V
= 3V
= 5V
= 5V
= 3V
= 5V
*NOTICE:
CC
0.7V
0.6V
0.9V
Min.
-0.5
-0.5
-0.5
power off.
4.2
2.5
4.2
2.5
-1
CC
CC
CC
(4)
(4)
(4)
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent dam-
age to the device. This is a stress rating only and
functional operation of the device at these or
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect
device reliability.
Typ.
(1)
0.2V
0.3V
0.2V
V
V
V
CC
CC
CC
Max.
0.7
0.5
0.7
0.5
1
+ 0.5
+ 0.5
+ 0.5
CC
CC
CC
(2)
(2)
(2)
Table 17-13 on
Units
µA
V
V
V
V
V
V
V
V
V
V
V
V
V
V
115