ATtiny13A Atmel Corporation, ATtiny13A Datasheet - Page 3

• Manufacturer Part Number: ATtiny13A
• Manufacturer: Atmel Corporation

Specifications of ATtiny13A

• Flash (kbytes): 1 Kbytes
• Pin Count: 8
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 6
• Ext Interrupts: 6
• Usb Speed: No
• Usb Interface: No
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 4
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.06
• Eeprom (bytes): 64
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 125
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 1
• Output Compare Channels: 2
• Pwm Channels: 2
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

Table 1-1.
Notes:
1.3
1.3.1
It is possible to manually calibrate the internal oscillator to be more accurate than default factory calibration. Note that the
oscillator frequency depends on temperature and voltage. Voltage and temperature characteristics can be found in
2-53 on page
Table 1-2.
Notes:
8126E-Appendix A–AVR–08/11
Symbol
Calibration
Method
Factory
Calibration
User
Calibration
I
CC
1. “Max” means the highest value where the pin is guaranteed to be read as low.
2. Not tested in production.
3. “Min” means the lowest value where the pin is guaranteed to be read as high.
4. Although each I/O port can under non-transient, steady state conditions sink more than the test conditions, the sum of all I
5. Although each I/O port can under non-transient, steady state conditions source more than the test conditions, the sum of all
6. Measured with all I/O modules turned off (PRR = 0xFF).
Clock Characteristics
1. Accuracy of oscillator frequency at calibration point (fixed temperature and fixed voltage).
Accuracy of Calibrated Internal Oscillator
(for all ports) should not exceed 60 mA. If I
not guaranteed to sink current greater than the listed test condition.
I
are not guaranteed to source current greater than the listed test condition.
OH
Parameter
Supply Current,
Active Mode
Supply Current,
Idle Mode
Supply Current,
Power-Down Mode
32,
(for all ports) should not exceed 60 mA. If I
Calibration Accuracy of Internal Oscillator
DC Characteristics, T
Figure 2-54 on page
4 – 5 MHz / 8 – 10 MHz
Fixed frequency within:
(6)
Target Frequency
4.8 / 9.6 MHz
A
= -40°C to +105°C (Continued)
33,
Condition
f = 1MHz, V
f = 4MHz, V
f = 8MHz, V
f = 1MHz, V
f = 4MHz, V
f = 8MHz, V
WDT enabled, V
WDT disabled, V
Figure 2-55 on page
Fixed voltage within:
OL
CC
CC
CC
CC
CC
CC
exceeds the test condition, V
OH
1.8V – 5.5V
= 2V
= 3V
= 5V
= 2V
= 3V
= 5V
CC
CC
exceeds the test condition, V
V
3V
= 3V
= 3V
CC
33, and in
Min
Figure 2-56 on page
Fixed temperature
-40°C to +105°C
Temperature
OL
within:
25°C
may exceed the related specification. Pins are
OH
may exceed the related specification. Pins
0.03
0.15
Typ
0.2
1.2
3.6
0.2
0.7
3.9
34.
Accuracy at given Voltage
Max
0.35
1.8
0.2
10
& Temperature
6
1
3
2
ATtiny13A
±10%
±2%
Units
mA
mA
mA
mA
mA
mA
µA
µA
(1)
Figure
OL
3