ATtiny24 Automotive Atmel Corporation, ATtiny24 Automotive Datasheet - Page 122

• Manufacturer Part Number: ATtiny24 Automotive
• Manufacturer: Atmel Corporation

Specifications of ATtiny24 Automotive

• Flash (kbytes): 2 Kbytes
• Pin Count: 14
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 4
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 12
• Ext Interrupts: 12
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.12
• Eeprom (bytes): 128
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 125
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

16. USI – Universal Serial Interface
16.1
16.2
122
Features
Overview
Atmel ATtiny24/44/84 [Preliminary]
•
•
•
•
•
•
The universal serial interface (USI) provides the basic hardware resources needed for serial
communication. Combined with a minimum of control software, the USI allows significantly
higher transfer rates and uses less code space than solutions based on software only. Inter-
rupts are included to minimize the processor load.
A simplified block diagram of the USI is shown in
placement of I/O pins, refer to
Registers, including I/O bits and I/O pins, are shown in bold. The device-specific I/O Register
and bit locations are listed in the
Figure 16-1. Universal Serial Interface, Block Diagram
The 8-bit shift register is directly accessible via the data bus and contains the incoming and
outgoing data. The register has no buffering, so the data must be read as quickly as possible
to ensure that no data are lost. The most significant bit is connected to one of two output pins,
depending on the wire mode configuration. A transparent latch is inserted between the serial
register output and output pin, which delays the change of data output to the opposite clock
edge of the data input sampling. The serial input is always sampled from the data input (DI)
pin independent of the configuration.
Two-wire Synchronous Data Transfer (Master or Slave)
Three-wire Synchronous Data Transfer (Master or Slave)
Data Received Interrupt
Wakeup from Idle Mode
In Two-wire Mode: Wakeup from All Sleep Modes, Including Power-down Mode
Two-wire Start Condition Detector with Interrupt Capability
USIDR
USISR
USICR
2
4-bit Counter
“Pinout Atmel
“Register Descriptions” on page
3
2
1
0
3
2
1
0
D Q
LE
®
[1]
ATtiny24/44/84” on page
TIM0 COMP
0
1
Figure 16-1 on page
Two-wire Clock
Control Unit
130.
CLOCK
HOLD
2. CPU accessible I/O
122. For the actual
DO
DI/SDA
USCK/SCL
7701E–AVR–02/11
(Output only)
(Input/Open Drain)
(Input/Open Drain)