ATtiny25 Automotive Atmel Corporation, ATtiny25 Automotive Datasheet - Page 129

• Manufacturer Part Number: ATtiny25 Automotive
• Manufacturer: Atmel Corporation

Specifications of ATtiny25 Automotive

• Flash (kbytes): 2 Kbytes
• Pin Count: 8
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 4
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 6
• Ext Interrupts: 6
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 4
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.12
• Eeprom (bytes): 128
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 125
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 5
• Pwm Channels: 6
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

16.3.5
16.3.6
16.4
16.4.1
16.4.2
16.4.3
16.4.4
16.4.5
7701E–AVR–02/11
Alternative USI Usage
Start Condition Detector
Clock speed considerations
Half-duplex Asynchronous Data Transfer
4-bit Counter
12-bit Timer/Counter
Edge-Triggered External Interrupt
Software Interrupt
The start condition detector is shown in
the range of 50 to 300ns) to ensure valid sampling of the SCL line. The start condition detector
is only enabled in two-wire mode.
The start condition detector is working asynchronously, and can, therefore, wake up the pro-
cessor from the power-down sleep mode. However, the protocol used might have restrictions
on the SCL hold time. Therefore, when using this feature in this case, the oscillator start-up
time set by the CKSEL fuses (see
also be taken into consideration. See the USISIF bit description in
ister” on page 130
Maximum frequency for SCL and SCK is f
receive rate in both two- and three-wire mode. In two-wire slave mode the two-wire clock con-
trol unit will hold SCL low until the slave is ready to receive more data. This may reduce the
actual data rate in two-wire mode.
When the USI unit is not used for serial communication, it can be set up to do alternative tasks
due to its flexible design.
By utilizing the Shift Register in Three-wire mode, it is possible to implement a more compact
and higher performance UART than by software only.
The 4-bit counter can be used as a stand-alone counter with overflow interrupt. Note that if the
counter is clocked externally, both clock edges will generate an increment.
Combining the USI 4-bit counter and Timer/Counter0 allows them to be used as a 12-bit
counter.
By setting the counter to maximum value (F), it can function as an additional external interrupt.
The overflow flag and interrupt enable bit are then used for the external interrupt. This feature
is selected by the USICS1 bit.
The counter overflow interrupt can be used as a software interrupt triggered by a clock strobe.
for further details.
Atmel ATtiny24/44/84 [Preliminary]
“Clock Systems and their Distribution” on page
Figure 16-6 on page
CK
/4. This is also the maximum data transmit and
128. The SDA line is delayed (in
“USISR – USI Status Reg-
25) must
129