SAM4S16C Atmel Corporation, SAM4S16C Datasheet - Page 535

• Manufacturer Part Number: SAM4S16C
• Manufacturer: Atmel Corporation

Specifications of SAM4S16C

• Flash (kbytes): 1024 Kbytes
• Pin Count: 100
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 79
• Ext Interrupts: 79
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1000
• Analog Comparators: 1
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

28. Parallel Input/Output Controller (PIO)
28.1
28.2
11100A–ATARM–28-Oct-11
11100A–ATARM–28-Oct-11
Description
Embedded Characteristics
The Parallel Input/Output Controller (PIO) manages up to 32 fully programmable input/output
lines. Each I/O line may be dedicated as a general-purpose I/O or be assigned to a function of
an embedded peripheral. This assures effective optimization of the pins of a product.
Each I/O line is associated with a bit number in all of the 32-bit registers of the 32-bit wide User
Interface.
Each I/O line of the PIO Controller features:
The PIO Controller also features a synchronous output providing up to 32 bits of data output in a
single write operation.
An 8-bit parallel capture mode is also available which can be used to interface a CMOS digital
image sensor, an ADC, a DSP synchronous port in synchronous mode, etc...
• An input change interrupt enabling level change detection on any I/O line.
• Additional Interrupt modes enabling rising edge, falling edge, low level or high level detection
• A glitch filter providing rejection of glitches lower than one-half of PIO clock cycle.
• A debouncing filter providing rejection of unwanted pulses from key or push button
• Multi-drive capability similar to an open drain I/O line.
• Control of the pull-up and pull-down of the I/O line.
• Input visibility and output control.
• Up to 32 Programmable I/O Lines
• Fully Programmable through Set/Clear Registers
• Multiplexing of Four Peripheral Functions per I/O Line
• For each I/O Line (Whether Assigned to a Peripheral or Used as General Purpose I/O)
• Synchronous Output, Provides Set and Clear of Several I/O lines in a Single Write
• Write Protect Registers
• Programmable Schmitt Trigger Inputs
• Parallel Capture Mode
on any I/O line.
operations.
– Input Change Interrupt
– Programmable Glitch Filter
– Programmable Debouncing Filter
– Multi-drive Option Enables Driving in Open Drain
– Programmable Pull Up on Each I/O Line
– Pin Data Status Register, Supplies Visibility of the Level on the Pin at Any Time
– Additional Interrupt Modes on a Programmable Event: Rising Edge, Falling Edge,
– Lock of the Configuration by the Connected Peripheral
Low Level or High Level
SAM4S
SAM4S
535
535