AD9257 Analog Devices, AD9257 Datasheet - Page 20

• Manufacturer Part Number: AD9257
• Description: Octal, 14-Bit, 40/65 MSPS Serial LVDS 1.8 V A/D Converter
• Manufacturer: Analog Devices

AD9257
If the internal reference of the
converters to improve gain matching, the loading of the reference
by the other converters must be considered. Figure 48 shows
how the internal reference voltage is affected by loading.
External Reference Operation
The use of an external reference may be necessary to enhance
the gain accuracy of the ADC or improve thermal drift charac-
teristics. Figure 49 shows the typical drift characteristics of the
internal reference in 1.0 V mode.
When the SENSE pin is tied to AVDD, the internal reference is
disabled, allowing the use of an external reference. An internal
reference buffer loads the external reference with an equivalent
7.5 kΩ load (see Figure 42). The internal buffer generates the
positive and negative full-scale references for the ADC core.
Therefore, the external reference must be limited to a maximum
of 1.0 V. It is not recommended to leave the SENSE pin floating.
–0.5
–1.0
–1.5
–2.0
–2.5
–3.0
–3.5
–4.0
–4.5
–5.0
–2
–4
–6
–8
4
2
0
0
–40
0
0.5
Figure 48. V
–15
Figure 49. Typical V
1.0
LOAD CURRENT (mA)
TEMPERATURE (°C)
REF
10
Error vs. Load Current
AD9257
1.5
REF
35
INTERNAL V
is used to drive multiple
Drift
2.0
60
REF
2.5
= 1V
3.0
85
Rev. 0 | Page 20 of 40
CLOCK INPUT CONSIDERATIONS
For optimum performance, clock the
CLK+ and CLK−, with a differential signal. The signal is typically
ac-coupled into the CLK+ and CLK− pins via a transformer or
capacitors. These pins are biased internally (see Figure 36) and
require no external bias.
Clock Input Options
The
input can be a CMOS, LVDS, LVPECL, or sine wave signal.
Regardless of the type of signal being used, clock source jitter is
of the utmost concern, as described in the Jitter Considerations
section.
Figure 50 and Figure 51 show two preferred methods for clock-
ing the
internal CLK divider). A low jitter clock source is converted
from a single-ended signal to a differential signal using either
an RF transformer or an RF balun.
The RF balun configuration is recommended for clock frequencies
between 65 MHz and 520 MHz, and the RF transformer is recom-
mended for clock frequencies from 10 MHz to 200 MHz. The
back-to-back Schottky diodes across the transformer/balun
secondary winding limit clock excursions into the
approximately 0.8 V p-p differential.
This limit helps prevent the large voltage swings of the clock
from feeding through to other portions of the
preserving the fast rise and fall times of the signal that are critical
to a low jitter performance. However, the diode capacitance comes
into play at frequencies above 500 MHz. Care must be taken in
choosing the appropriate signal limiting diode.
CLOCK
INPUT
CLOCK
INPUT
AD9257
Figure 50. Transformer-Coupled Differential Clock (Up to 200 MHz)
Figure 51. Balun-Coupled Differential Clock (65 MHz to 520 MHz)
AD9257
50Ω
0.1µF
has a very flexible clock input structure. The clock
50Ω
0.1µF
0.1µF
(at clock rates of up to 520 MHz prior to the
100Ω
ADT1-1WT, 1:1 Z
Mini-Circuits
XFMR
0.1µF
®
0.1µF
0.1µF
0.1µF
0.1µF
AD9257
SCHOTTKY
HSMS2822
SCHOTTKY
HSMS2822
DIODES:
DIODES:
AD9257
sample clock inputs,
Data Sheet
CLK+
CLK–
AD9257
CLK+
CLK–
ADC
while
ADC
to