AD9629 Analog Devices, AD9629 Datasheet - Page 26

no-image

AD9629

Manufacturer Part Number
AD9629
Description
12-Bit, 20/40/65/80 MSPS, 1.8 V Analog-to-Digital Converter
Manufacturer
Analog Devices
Datasheet

Specifications of AD9629

Resolution (bits)
12bit
# Chan
1
Sample Rate
80MSPS
Interface
Par
Analog Input Type
Diff-Uni
Ain Range
2 V p-p
Adc Architecture
Pipelined
Pkg Type
CSP

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD9629BCPZ-20
Manufacturer:
Analog Devices Inc
Quantity:
135
Part Number:
AD9629BCPZ-40
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD9629BCPZ-65
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD9629BCPZ-80
Manufacturer:
ADI/亚德诺
Quantity:
1 000
Part Number:
AD9629BCPZRL7-65
Manufacturer:
ADI/亚德诺
Quantity:
20 000
AD9629
MEMORY MAP
READING THE MEMORY MAP REGISTER TABLE
Each row in the memory map register table (see Table 16)
contains eight bit locations. The memory map is roughly
divided into four sections: the chip configuration registers
(Address 0x00 to Address 0x02); the device transfer register
(Address 0xFF); the program registers, including setup, control,
and test (Address 0x08 to Address 0x2A); and the AD9629
specific customer SPI control register (Address 0x101).
Table 16 documents the default hexadecimal value for each
hexadecimal address shown. The column with the heading Bit 7
(MSB) is the start of the default hexadecimal value given. For
example, Address 0x2A, the OR/MODE select register, has a hexa-
decimal default value of 0x01. This means that in Address 0x2A,
Bits[7:1] = 0, and Bit 0 = 1. This setting is the default OR/MODE
setting. The default value results in the programmable external
MODE/OR pin (Pin 23) functioning as an out-of-range digital
output. For more information on this function and others, see the
AN-877 Application Note, Interfacing to High Speed ADCs via SPI.
This application note details the functions controlled by Register
0x00 to Register 0xFF. The remaining register, Register 0x101, is
documented in the Memory Map section that follows Table 16.
OPEN LOCATIONS
All address and bit locations that are not included in the SPI map
are not currently supported for this device. Unused bits of a valid
address location should be written with 0s. Writing to these loca-
tions is required only when part of an address location is open
(for example, Address 0x2A). If the entire address location is
open, it is omitted from the SPI map (for example, Address 0x13)
and should not be written.
Rev. 0 | Page 26 of 32
DEFAULT VALUES
After the AD9629 is reset, critical registers are loaded with default
values. The default values for the registers are given in the memory
map register table (see Table 16).
Logic Levels
An explanation of logic level terminology follows:
Transfer Register Map
Address 0x08 to Address 0x18 are shadowed. Writes to these
addresses do not affect part operation until a transfer command
is issued by writing 0x01 to Address 0xFF, setting the transfer bit.
This allows these registers to be updated internally and simulta-
neously when the transfer bit is set. The internal update takes
place when the transfer bit is set, and then the bit autoclears.
“Bit is set” is synonymous with “bit is set to Logic 1” or
“writing Logic 1 for the bit. ”
“Clear a bit” is synonymous with “bit is set to Logic 0” or
“writing Logic 0 for the bit. ”

Related parts for AD9629