AD10200 Analog Devices, AD10200 Datasheet
AD10200
Specifications of AD10200
Available stocks
Related parts for AD10200
AD10200 Summary of contents
Page 1
... The AD10200 operates with 5.0 V supply for the analog-to- digital conversion. Each channel is completely independent allowing operation with independent encode and analog inputs. The AD10200 is packaged in a 68-lead ceramic chip carrier package. Manufacturing is done on Analog Devices, Inc. MIL- 38534 Qualified Manufacturers Line (QML) and components are available up to Class-H (– ...
Page 2
... AD10200–SPECIFICATIONS Parameter RESOLUTION DC ACCURACY Differential Nonlinearity Integral Nonlinearity No Missing Codes 2 Gain Error Output Offset ANALOG INPUT Input Voltage Range Input Impedance 3 Input VSWR Analog Input Bandwidth, High Analog Input Bandwidth, Low ANALOG REFERENCE Output Voltage Load Current Tempco SWITCHING PERFORMANCE ...
Page 3
... I 4 Full 25°C V Full V 25°C V Full V 25° Full Full IV 12 A2) grounded and a full-scale signal applied to B Channel (A IN AD10200 Min Typ Max Unit 66 dBFS 63 dBFS 63 65.5 dBFS 60.5 63 dBFS 61 63.5 dBFS 57 60 dBFS 56 58.5 dBFS 53 55 dBFS ...
Page 4
... ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD10200 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Table I. Output Coding (VREF = 2.5 V) (Two’ ...
Page 5
... B Channel Analog Ground. A and B grounds should be connected as close to the device as possible. Digital Outputs for ADC B. D0 (LSB) B Channel Digital Ground Digital Positive Supply Voltage (Nominally 3.3 V) Data conversion initiated on rising edge of ENCODE input. Complement of Encode B Channel Internal Voltage Reference Analog Input for B Side ADC AD10200 61 60 AGNDB 59 AGNDB 58 DNC 57 ...
Page 6
... AD10200 DEFINITION OF SPECIFICATIONS Analog Bandwidth The analog input frequency at which the spectral power of the fundamental frequency (as determined by the FFT analysis) is reduced by 3 dB. Aperture Delay The delay between the 50% point on the rising edge of the ENCODE command and the instant at which the analog input is sampled ...
Page 7
... AD10200 FREQUENCY – MHz ENCODE = 105 MSPS A = 121MHz (–1dBFS) IN SNR = 64.92dBFS SFDR = 64.73dBc FREQUENCY – MHz ENCODE = 105 MSPS A = 201MHz (– ...
Page 8
... AD10200 0 ENCODE = 105 MSPS 37MHz & 38MHz (–10dBFS SFDR = 79.84dBc 100 110 120 130 FREQUENCY – MHz 0 ENCODE = 105 MSPS 120MHz & 121MHz (–7dBFS SFDR = 63.8dBc 100 110 ...
Page 9
... SAMPLE N+10 SAMPLE N+1 SAMPLE N+9 DATA DATA N 1 17k ENCODE AD10200 62.4 92.1 121.8 151.5 181.2 210.9 240.6 270.3 300.0 MHz SAMPLE N+11 1 DATA N DATA NPN V OUTPUT REF V CC ...
Page 10
... A/D output. For that reason, considerable care has been taken in the design of the ENCODE input of the AD10200, and the user is advised to give commensurate thought to the clock source. The ENCODE input are fully TTL/CMOS compatible. For opti- mum performance, the AD10200 must be clocked differentially ...
Page 11
... Power to the analog supply pins is connected via banana jacks. The analog supply powers the associated components and the analog section of the AD10200. The digital outputs of the AD10200 are powered via banana jacks with 3.3 V. Contact the factory if additional layout or applications assistance is required. AD10200 ...
Page 12
... AD10200 AGNDB AGNDB SDIN_B (NC) 64 AGNDA AGNDB 65 5VAB 5VAB_ 66 SCLK_B (NC) 67 AGNDB AGNDB 68 SHIELD LID 1 AGNDA AGNDA 2 REF_A 3 SDIN_A (NC) 4 AGNDA AGNDA VFU_A 5 AGNDA AGNDA 9 DGNDB DGNDB 43 D6B D6B 42 D7B D7B 41 D8B D8B ...
Page 13
... E29 E30 E36 E35 E38 E37 E39 E40 E45 E46 E79 E80 E84 E83 DGNDB AGNDB STAND OFFS ON THE BOARD SO1 SO4 SO2 SO5 SO3 SO6 AD10200 ENCAB ENCAB DGNDA C5 0.1 F LATCHA 8 +3.3VA VCC E23 E19 VEE BUFLATA DGNDA ...
Page 14
... AD10200 BILL OF MATERIALS LIST FOR AD10200 EVAL BOARD Qty. Component Name Ref Des 2 74LCX16373MTD U16, U17 1 AD10200BZ U1 2 ADP3330 U14, U15 4 BRES0805 R38, R39, R56, R58 4 BRES0805 R1, R41, R60, R61 8 BRES0805 R3, R4, R42, R43, R63, R64, R65, R66 23 CAP2 C1, C2, C5, C6, ...
Page 15
... AD10200 ...
Page 16
... AD10200 ...
Page 17
... AD10200 ...
Page 18
... AD10200 ...
Page 19
... Ceramic Leaded Chip Carrier (Z-68B) 0.290 (7.37) 0.960 (24.38) MAX 0.950 (24.13) SQ 0.940 (23.88 PIN 1 1.070 0.800 TOP VIEW (27.18) (20.32) (PINS DOWN) MIN BSC 26 27 DETAIL A 0.055 (1.40) 0.021 (0.533) 0.050 (1.27) 0.017 (0.432) 0.230 (5.84) MAX 0.045 (1.14) 0.014 (0.357) AD10200 61 60 1.190 (30.23) 1.180 (29.97) SQ 1.170 (29.72 Page ...
Page 20
...