ADP5040 Analog Devices, ADP5040 Datasheet - Page 29

• Manufacturer Part Number: ADP5040
• Description: Micro PMU with 1.2 A Buck Regulator and Two 300 mA LDOs
• Manufacturer: Analog Devices

Data Sheet
APPLICATIONS INFORMATION
BUCK EXTERNAL COMPONENT SELECTION
Trade-offs between performance parameters such as efficiency
and transient response are made by varying the choice of
external components in the applications circuit, as shown in
Figure 1.
Feedback Resistors
Referring to Figure 102, the total combined resistance for R1
and R2 is not to exceed 400 kΩ.
Inductor
The high switching frequency of the
the selection of small chip inductors. For best performance, use
inductor values between 0.7 μH and 3.0 μH. Suggested inductors
are shown in Table 8.
The peak-to-peak inductor current ripple is calculated using
the following equation:
where:
f
L is the inductor value.
The minimum dc current rating of the inductor must be greater
than the inductor peak current. The inductor peak current is
calculated using the following equation:
Table 8. Suggested 1.0 μH Inductors
Vendor
Murata
Murata
Tayo Yuden
Coilcraft
Coilcraft
Toko
Inductor conduction losses are caused by the flow of current
through the inductor, which has an associated internal dc
resistance (DCR). Larger sized inductors have smaller DCR,
which may decrease inductor conduction losses. Inductor core
losses are related to the magnetic permeability of the core material.
Because the buck is high switching frequency dc-to-dc converter,
shielded ferrite core material is recommended for its low core
losses and low EMI.
Output Capacitor
Higher output capacitor values reduce the output voltage ripple
and improve load transient response. When choosing the
capacitor value, it is also important to account for the loss of
capacitance due to output voltage dc bias.
SW
is the switching frequency.
I
I
RIPPLE
PEAK
=
=
I
LOAD
Model
LQM2MPN1R0NG0B
LQM18FN1R0M00B
CBC322ST1R0MR
XFL4020-102ME
XPL2010-102ML
MDT2520-CN
V
OUT
V
(
MAX
IN
×
(
×
V
)
f
IN
+
SW
I
−
RIPPLE
×
V
2
L
OUT
)
Dimensions
(mm)
2.0 × 1.6 × 0.9
3.2 × 2.5 × 1.5
3.2 × 2.5 × 2.5
4.0 × 4.0 × 2.1
1.9 × 2.0 × 1.0
2.5 × 2.0 × 1.2
ADP5040
buck allows for
I
(mA)
1400
2300
2000
5400
1800
1350
SAT
71
DCR
(mΩ)
85
54
11
89
85
Rev. 0 | Page 29 of 40
Ceramic capacitors are manufactured with a variety of dielec-
trics, each with a different behavior over temperature and
applied voltage. Capacitors must have a dielectric adequate
to ensure the minimum capacitance over the necessary
temperature range and dc bias conditions. X5R or X7R
dielectrics with a voltage rating of 6.3 V or 10 V are highly
recommended for best performance. Y5V and Z5U dielectrics
are not recommended for use with any dc-to-dc converter
because of their poor temperature and dc bias characteristics.
The worst-case capacitance accounting for capacitor variation
over temperature, component tolerance, and voltage is calcu-
lated using the following equation:
where:
C
TEMPCO is the worst-case capacitor temperature coefficient.
TOL is the worst-case component tolerance.
In this example, the worst-case temperature coefficient (TEMPCO)
over −40°C to +85°C is assumed to be 15% for an X5R dielectric.
The tolerance of the capacitor (TOL) is assumed to be 10%, and
C
Substituting these values in the equation yields
To guarantee the performance of the buck, it is imperative
that the effects of dc bias, temperature, and tolerances on the
behavior of the capacitors be evaluated for each application.
The peak-to-peak output voltage ripple for the selected output
capacitor and inductor values is calculated using the following
equation:
EFF
OUT
is the effective capacitance at the operating voltage.
C
C
V
is 9.2481 μF at 1.8 V, as shown in Figure 105.
EFF
EFF
RIPPLE
12
10
8
6
4
2
0
0
= C
= 9.24 μF × (1 − 0.15) × (1 − 0.1) = 7.07 μF
=
OUT
8
Figure 105. Typical Capacitor Performance
×
× (1 − TEMPCO) × (1 − TOL)
1
f
I
SW
RIPPLE
×
C
OUT
2
DC BIAS VOLTAGE (V)
≈
(
2
π
3
×
f
SW
V
)
2
IN
4
×
L
×
C
OUT
5
ADP5040
6