ADP5041 Analog Devices, ADP5041 Datasheet - Page 33

• Manufacturer Part Number: ADP5041
• Description: Micro PMU with 1.2 A Buck, Two 300 mA LDOs, Supervisory, Watchdog and Manual Reset
• Manufacturer: Analog Devices

Data Sheet
Table 13. Suggested 1.0 μF Capacitors
Vendor
Murata
TDK
Panasonic
Taiyo
Yuden
Input and Output Capacitor Properties
Use any good quality ceramic capacitor with the
long as it meets the minimum capacitance and maximum ESR
requirements. Ceramic capacitors are manufactured with a variety
of dielectrics, each with a different behavior over temperature
and applied voltage. Capacitors must have a dielectric adequate
to ensure the minimum capacitance over the necessary tempe-
rature range and dc bias conditions. X5R or X7R dielectrics
with a voltage rating of 6.3 V or 10 V are recommended for best
performance. Y5V and Z5U dielectrics are not recommended
for use with any LDO because of their poor temperature and dc
bias characteristics.
Figure 110 depicts the capacitance vs. dc voltage bias characteristic
of a 0402 1 µF, 10 V, X5R capacitor. The voltage stability of a
capacitor is strongly influenced by the capacitor size and voltage
rating. In general, a capacitor in a larger package or higher voltage
rating exhibits better stability. The temperature variation of the
X5R dielectric is about ±15% over the −40°C to +85°C tempera-
ture range and is not a function of package or voltage rating.
Use the following equation to determine the worst-case capa-
citance, accounting for capacitor variation over temperature,
component tolerance, and voltage.
where:
C
TEMPCO is the worst-case capacitor temperature coefficient.
TOL is the worst-case component tolerance.
In this example, the worst-case temperature coefficient
(TEMPCO) over −40°C to +85°C is assumed to be 15% for an
BIAS
C
is the effective capacitance at the operating voltage.
EFF
1.2
1.0
0.8
0.6
0.4
0.2
0
0
= C
Figure 110. Capacitance vs. Voltage Characteristic
BIAS
Type
X5R
X5R
X5R
X5R
× (1 − TEMPCO) × (1 − TOL)
1
Model
GRM155B30J105K
C1005JB0J105KT
ECJ0EB0J105K
LMK105BJ105MV-F
DC BIAS VOLTAGE (V)
2
3
4
Case Size
0402
0402
0402
0402
5
ADP5041
Voltage
Rating (V)
6.3
6.3
6.3
10.0
6
as
Rev. 0 | Page 33 of 40
X5R dielectric. The tolerance of the capacitor (TOL) is assumed
to be 10%, and C
Substituting these values into the following equation yields:
Therefore, the capacitor chosen in this example meets the
minimum capacitance requirement of the LDO over
temperature and tolerance at the chosen output voltage.
To guarantee the performance of the
that the effects of dc bias, temperature, and tolerances on the
behavior of the capacitors be evaluated for each application.
SUPERVISORY SECTION
Threshold Setting Resistors
Referring to Figure 105, the maximum value of R2 is not to
exceed 200 kΩ.
Watchdog Input Current
To minimize watchdog input current (and minimize overall
power consumption), leave WDI low for the majority of the
watchdog timeout period. When driven high, WDI can draw
as much as 25 µA. Pulsing WDI low-to-high-to-low at a low
duty cycle reduces the effect of the large input current. When
WDI is unconnected, a window comparator disconnects the
watchdog timer from the reset output circuitry so that reset is
not asserted when the watchdog timer times out.
Negative-Going Transients at the Monitored Rail
To avoid unnecessary resets caused by fast power supply transients,
the
performance characteristic in Figure 111 plots the monitored
rail voltage, V
The curve shows combinations of transient magnitude and
duration for which a reset is not generated. In this example,
with the 3.00 V threshold, a transient that goes 100 mV below
the threshold and lasts 8 µs typically does not cause a reset, but
if the transient is any larger in magnitude or duration, a reset is
generated. In this example, the reset threshold programming
resistor values were R2 = 200 kΩ, R1 = 1 MΩ (see Figure 105).
ADP5041
C
900
800
700
600
500
400
300
200
100
EFF
0
0.1
= 0.94 μF × (1 − 0.15) × (1 − 0.1) = 0.72 μF
Figure 111. Maximum V
is equipped with glitch rejection circuitry. The typical
TH
, transient duration vs. the transient magnitude.
BIAS
COMPARATOR OVERDRIVE (% OF V
is 0.94 μF at 1.8 V, as shown in Figure 110.
Threshold Overdrive
1
TH
Transient Duration vs. Reset
ADP5041
10
, it is imperative
TH
)
ADP5041
100