IC DGTL AUDIO PWM PROC 64-TQFP

TAS5508APAG

Manufacturer Part NumberTAS5508APAG
DescriptionIC DGTL AUDIO PWM PROC 64-TQFP
ManufacturerTexas Instruments
TypePWM Processor
TAS5508APAG datasheet
 


Specifications of TAS5508APAG

ApplicationsDVDMounting TypeSurface Mount
Package / Case64-TQFP, 64-VQFPFor Use WithTAS5342DDV6EVM - TAS5342DDV6EVMTAS5508-5142K7EVM - EVAL MODULE FOR TAS5508B/TAS5142TAS5508-5122C6EVM - EVAL MODULE FOR TAS5508B/TAS5122TAS5508-5121K8EVM - EVAL MODULE FOR TAS5508B/TAS5121
Lead Free Status / RoHS StatusLead free / RoHS CompliantOther names296-17475
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Page 41
42
Page 42
43
Page 43
44
Page 44
45
Page 45
46
Page 46
47
Page 47
48
Page 48
49
Page 49
50
Page 50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
Page 44/105

Download datasheet (2Mb)Embed
PrevNext
TAS5508A
8-Channel Digital Audio PWM Processor
SLES119A – FEBRUARY 2004 – REVISED JULY 2009
Because RESET is an asynchronous signal, clicks and pops produced during the application (the leading
edge) of RESET cannot be avoided. However, the transition from the hard mute state (M) to the
operational state is performed using a quiet start-up sequence to minimize noise. This control uses the
PWM reset and unmute sequence to shut down and start up the PWM. A detailed description of these
sequences is contained in the PWM section. If a completely quiet reset or power-down sequence is
desired, MUTE should be applied before applying RESET.
The rising edge of the reset pulse begins device initialization before the transition to the operational mode.
During device initialization, all controls are reset to their initial states.
settings following a reset.
CONTROL
Clock register
High pass
Unmute from clock error
PSVC Hi-Z
Post DAP detection automute
Eight Ch PreDAP detection automute
De-emphasis
Channel configuration control
Headphone configuration control
Serial data interface format
Individual channel mute
Automute delay
Automute threshold 1
Automute threshold 2
Modulation limit
Six- (or eight – low) channel configuration
Slew rate limit
Interchannel delay
Shutdown PWM on error
Volume and mute update rate
Treble and bass slew rate
Bank switching
Auto bank-switching map
Biquad coefficients (5508)
Input mixer coefficients
Output mixer coefficients
Subwoofer sum into Ch1 and Ch2 (5508)
Ch1 and Ch2 sum in subwoofer (5508)
Bass and treble bypass
Bass and treble inline
DRC bypass (5508)
DRC inline (5508)
DRC (5508)
Master volume
Individual channel volumes
All bass and treble Indexes
Treble filter sets
44
TAS5508A Controls and Status
Table 3-2. Values Set During Reset
Not valid
Disabled
Hard unmute
Disabled
Enabled
Enabled
De-emphasis disabled
Configured for the default setting
Configured for the default setting
2
I
S 24 bit
No channels are muted
5 ms
< 8 bits
Same as automute threshold 1
Maximum modulation limit of 97.7%
Eight channels
Disengaged for all channels
–32, 0, –16, 16, –24, 8, –8, –24
Enabled
Volume ramp 85 ms
Update every 1.31 ms
Manual bank selection is enabled
All channels use bank 1
Set to all pass
Input N -> Channel N, no attenuation
Channel N -> Output N, no attenuation
Gain of 0
Gain of 0
Gain of 1
Gain of 0
Gain of 1
Gain of 0
DRC disabled, default values
Mute
0 dB
0x12 neutral
Filter set 3
www.ti.com
Table 3-2
shows the default control
SETTING
Submit Documentation Feedback