IC DGTL AUDIO PWM PROC 64-TQFP

TAS5508APAG

Manufacturer Part NumberTAS5508APAG
DescriptionIC DGTL AUDIO PWM PROC 64-TQFP
ManufacturerTexas Instruments
TypePWM Processor
TAS5508APAG datasheet
 


Specifications of TAS5508APAG

ApplicationsDVDMounting TypeSurface Mount
Package / Case64-TQFP, 64-VQFPFor Use WithTAS5342DDV6EVM - TAS5342DDV6EVMTAS5508-5142K7EVM - EVAL MODULE FOR TAS5508B/TAS5142TAS5508-5122C6EVM - EVAL MODULE FOR TAS5508B/TAS5122TAS5508-5121K8EVM - EVAL MODULE FOR TAS5508B/TAS5121
Lead Free Status / RoHS StatusLead free / RoHS CompliantOther names296-17475
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
Page 51
52
Page 52
53
Page 53
54
Page 54
55
Page 55
56
Page 56
57
Page 57
58
Page 58
59
Page 59
60
Page 60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
Page 52/105

Download datasheet (2Mb)Embed
PrevNext
TAS5508A
8-Channel Digital Audio PWM Processor
SLES119A – FEBRUARY 2004 – REVISED JULY 2009
3.5.1 Manual Bank Selection
The three bank selection bits of the bank control register allow the appropriate bank to be manually
selected (000 = bank 1, 001 = bank 2, 010 = bank 3). In the manual mode, when a write occurs to the
biquad, DRC, or loudness coefficients, the currently selected bank is updated. If audio data is streaming to
the TAS5508A during a manual bank selection, the TAS5508A first performs a mute sequence, then
performs the bank switch, and finally restores the volume using an unmute sequence.
A mute command initiated by the bank-switch mute sequence overrides an unmute command or a volume
command. While a mute is active, the commanded channels are muted. When a channel is unmuted, the
volume level goes to the last commanded volume setting that has been received for that channel.
If MCLK or SCLK is stopped, the TAS5508A performs a bank-switch operation. If the clocks start up once
the manual bank-switch command has been received, the bank-switch operation is performed during the
5-ms, silent-start sequence.
3.5.2 Automatic Bank Selection
To enable automatic bank selection, a value of 3 is written into the bank selection bits of the bank control
register. Banks are associated with one or more sample rates by writing values into the bank 1 or bank 2
data-rate selection registers. The automatic bank selection is performed when a frequency change is
detected according to the following scheme:
1. The system scans bank-1 data-rate associations to see if bank 1 is assigned for that data rate.
2. If bank 1 is assigned, then the bank-1 coefficients are loaded.
3. If bank 1 is not assigned, the system scans bank 2 to see if bank 2 is assigned for that data rate.
4. If bank 2 is assigned, the bank-2 coefficients are loaded.
5. If bank 2 is not assigned, the system loads the bank-3 coefficients.
The default is that all frequencies are enabled for bank 1. This default is expressed as a value of all 1s in
the bank-1 auto-selection byte and all 0s in the bank-2 auto-selection byte.
3.5.2.1 Coefficient Write Operations While Automatic Bank Switch Is Enabled
In automatic mode, if a write occurs to the tone, EQ, DRC, or loudness coefficients, the bank that is
written to is the current bank.
3.5.3 Bank Set
Bank set is used to provide a secure way to update the bank coefficients in both the manual and
automatic switching modes without causing a bank switch to occur. Bank-set mode does not alter the
current bank register mapping. It simply enables any bank coefficients to be updated while inhibiting any
bank switches from taking place. In manual mode, this enables the coefficients to be set without switching
banks. In automatic mode, this prevents a clock error or data rate change from corrupting a bank
coefficient write.
To update the coefficients of a bank, a value of 4, 5, or 6 is written into in the bank selection-bits of the
bank control register. This enables the tone, EQ, DRC, and loudness coefficient values of bank 1, 2, or 3,
respectively, to be updated.
Once the coefficients of the bank have been updated, the bank-selection bits are then returned to the
desired manual or automatic bank-selection mode.
3.5.4 Bank-Switch Timeline
After a bank switch is initiated (manual or automatic), no I
a minimum of 186 ms. This value is determined by the volume ramp rates for a particular sample rate.
52
TAS5508A Controls and Status
2
C writes to the TAS5508A should occur before
Submit Documentation Feedback
www.ti.com