LPC2420_60

Manufacturer Part NumberLPC2420_60
DescriptionNXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
ManufacturerNXP Semiconductors
LPC2420_60 datasheet
 


1
2
3
4
5
6
7
8
9
10
11
Page 11
12
Page 12
13
Page 13
14
Page 14
15
Page 15
16
Page 16
17
Page 17
18
Page 18
19
Page 19
20
Page 20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
Page 11/86

Download datasheet (497Kb)Embed
PrevNext
NXP Semiconductors
Table 4.
Pin description
…continued
Symbol
Pin
[1]
P0[11]/RXD2/
100
SCL2/MAT3[1]
[2]
P0[12]/
41
USB_PPWR2/
MISO1/AD0[6]
[2]
P0[13]/
45
USB_UP_LED2/
MOSI1/AD0[7]
[1]
P0[14]/
69
USB_HSTEN2/
USB_CONNECT2/S
SEL1
[1]
P0[15]/TXD1/
128
SCK0/SCK
[1]
P0[16]/RXD1/
130
SSEL0/SSEL
[1]
P0[17]/CTS1/
126
MISO0/MISO
[1]
P0[18]/DCD1/
124
MOSI0/MOSI
LPC2420_60
Product data sheet
Ball
Type
Description
[1]
R14
I/O
P0[11] — General purpose digital input/output pin.
I
RXD2 — Receiver input for UART2.
2
I/O
SCL2 — I
C2 clock input/output (this is not an open-drain pin).
O
MAT3[1] — Match output for Timer 3, channel 1.
[2]
R1
I/O
P0[12] — General purpose digital input/output pin.
O
USB_PPWR2 — Port Power enable signal for USB port 2.
I/O
MISO1 — Master In Slave Out for SSP1.
I
AD0[6] — A/D converter 0, input 6.
[2]
R2
I/O
P0[13] — General purpose digital input/output pin.
O
USB_UP_LED2 — USB port 2 GoodLink LED indicator. It is LOW
when device is configured (non-control endpoints enabled), or when
host is enabled and has detected a device on the bus. It is HIGH
when the device is not configured, or when host is enabled and has
not detected a device on the bus, or during global suspend. It
transitions between LOW and HIGH (flashes) when host is enabled
and detects activity on the bus.
I/O
MOSI1 — Master Out Slave In for SSP1.
I
AD0[7] — A/D converter 0, input 7.
[1]
T7
I/O
P0[14] — General purpose digital input/output pin.
O
USB_HSTEN2 — Host Enabled status for USB port 2.
O
USB_CONNECT2 — SoftConnect control for USB port 2. Signal used
to switch an external 1.5 k resistor under software control. Used with
the SoftConnect USB feature.
I/O
SSEL1 — Slave Select for SSP1.
[1]
J16
I/O
P0[15] — General purpose digital input/output pin.
O
TXD1 — Transmitter output for UART1.
I/O
SCK0 — Serial clock for SSP0.
I/O
SCK — Serial clock for SPI.
[1]
J14
I/O
P0 [16] — General purpose digital input/output pin.
I
RXD1 — Receiver input for UART1.
I/O
SSEL0 — Slave Select for SSP0.
I/O
SSEL — Slave Select for SPI.
[1]
K17
I/O
P0[17] — General purpose digital input/output pin.
I
CTS1 — Clear to Send input for UART1.
I/O
MISO0 — Master In Slave Out for SSP0.
I/O
MISO — Master In Slave Out for SPI.
[1]
K15
I/O
P0[18] — General purpose digital input/output pin.
I
DCD1 — Data Carrier Detect input for UART1.
I/O
MOSI0 — Master Out Slave In for SSP0.
I/O
MOSI — Master Out Slave In for SPI.
All information provided in this document is subject to legal disclaimers.
Rev. 6.1 — 22 September 2011
LPC2420/2460
Flashless 16-bit/32-bit microcontroller
© NXP B.V. 2011. All rights reserved.
11 of 86