MCP6546-E/P Microchip Technology, MCP6546-E/P Datasheet
MCP6546-E/P
Specifications of MCP6546-E/P
Available stocks
Related parts for MCP6546-E/P
MCP6546-E/P Summary of contents
Page 1
... IN IN © 2007 Microchip Technology Inc. Description The Microchip Technology Inc. MCP6546/6R/6U/7/8/9 family of comparators is offered in single (MCP6546, + 0.3V MCP6546R, MCP6546U), single with chip select (CS) (MCP6548), dual (MCP6547) and quad (MCP6549) configurations. The outputs are open-drain and are capable of driving heavy DC or capacitive loads. ...
Page 2
... Current at Input Pins ....................................................±2 mA Current at Output and Supply Pins ............................±30 mA Storage temperature .....................................-65°C to +150°C Maximum Junction Temperature (T ) .......................... +150°C J ESD protection on all pins: (HBM;MM) .....................................2 kV;200V (MCP6546U) (HBM;MM) ................................ 4 kV; 200V (all other parts) DC CHARACTERISTICS Electrical Specifications: Unless otherwise indicated 2.74 kΩ ...
Page 3
... PDS Maximum Toggle Frequency f MAX f MAX Input Noise Voltage E Note 1: t and t depend on the load (R R PLH 2: Propagation Delay Skew is defined as: t © 2007 Microchip Technology Inc. MCP6546/6R/6U/7/8/9 = +1.6V to +5.5V GND 1-3). Min Typ Max Units 1.6 — -100 — — ...
Page 4
... MCP6546/6R/6U/7/8/9 MCP6548 CHIP SELECT (CS) CHARACTERISTICS Electrical Specifications: Unless otherwise indicated 2.74 kΩ and (Refer to Figures Parameters Sym CS Low Specifications CS Logic Threshold, Low Input Current, Low I CSL CS High Specifications CS Logic Threshold, High Input Current, High I CSH CS Input High, V Current Input High, GND Current ...
Page 5
... Thermal Resistance, 8L-MSOP Thermal Resistance, 14L-PDIP Thermal Resistance, 14L-SOIC Thermal Resistance, 14L-TSSOP Note: The MCP6546/6R/6U/7/8/9 I-temp family operates over this extended temperature range, but with reduced performance. In any case, the Junction Temperature (T specification of +150°C. 1.1 Test Circuit Configuration This test circuit configuration is used to determine the AC and DC specifications ...
Page 6
... FIGURE 2-2: Input Offset Voltage Drift 5. OUT – Time (1 ms/div) FIGURE 2-3: The MCP6546/6R/6U/7/8/9 comparators show no phase reversal. DS21714F-page 6 = +1.6V to +5.5V GND +25° 18% 1200 Samples 16 14% 12% 10 1.6 2.0 2.4 2.8 3.2 3.6 4.0 4.4 4.8 5.2 5.6 6.0 FIGURE 2- 25% 20% 15% 10 ...
Page 7
... T = +85°C -1 +125°C A -1.5 -2.0 Common Mode Input Voltage (V) FIGURE 2-9: Input Offset Voltage vs. Common Mode Input Voltage © 2007 Microchip Technology Inc. MCP6546/6R/6U/7/8/9 = +1.6V to +5.5V GND 6.5 V 6.0 CM 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 ...
Page 8
... MCP6546/6R/6U/7/8/9 Note: Unless otherwise indicated 2.74 kΩ and pF Input Referred PSRR 1. CMRR -0.3 to 5.3V 5. -50 - Ambient Temperature (°C) FIGURE 2-13: CMRR,PSRR vs. Ambient Temperature. 1000 100 0 105 Ambient Temperature (°C) FIGURE 2-14: Input Bias Current, Input Offset Current vs. Ambient Temperature. ...
Page 9
... A 0 -40°C A 0.3 0.2 0.1 0.0 0.0 0.2 0.4 0.6 0.8 1.0 Output Current (mA) FIGURE 2-21: Output Voltage Headroom vs. Output Current 1.6V. DD © 2007 Microchip Technology Inc. MCP6546/6R/6U/7/8/9 = +1.6V to +5.5V GND 5. (V) FIGURE 2-22: to Supply Voltage Difference. ...
Page 10
... MCP6546/6R/6U/7/8/9 Note: Unless otherwise indicated 2.74 kΩ and pF 50% 408 Samples 45% 100 mV Overdrive 40 35% 30% 25% 20 High-to-Low Propagation Delay (µs) FIGURE 2-25: High-to-Low Propagation Delay. 50% 45 5.5V 100 mV Overdrive DD 40% 35% 30% 25 1.6V DD 20% 15% 10 Propagation Delay Skew (µs) FIGURE 2-26: Propagation Delay Skew ...
Page 11
... Pull-up Voltage (V) FIGURE 2-33: Propagation Delay vs. Pull-up Voltage. © 2007 Microchip Technology Inc. MCP6546/6R/6U/7/8/9 = +1.6V to +5.5V GND 5. 100 mV Overdrive 1.2 1.4 1.6 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 FIGURE 2-34: = 1.6V. Common Mode Input Voltage at V ...
Page 12
... MCP6546/6R/6U/7/8/9 Note: Unless otherwise indicated 2.74 kΩ and pF 1.E-03 1m Comparator 1.E-04 100µ Turns On 10µ 1.E-05 1.E-06 1µ CS Hysteresis 1.E-07 100n 1.E-08 10n CS 1.E-09 1n High-to-Low 1.E-10 100p V = 1.6V DD 1.E-11 10p 0.0 0.2 0.4 0.6 0.8 1.0 Chip Select (CS) Voltage (V) FIGURE 2-37: Supply Current (shoot through current) vs ...
Page 13
... This is a CMOS, Schmitt-triggered input that places the part into a low power mode of operation. 3.3 Digital Outputs The comparator outputs are CMOS, open-drain digital outputs. They are designed to make level shifting and wired-OR easy to implement. © 2007 Microchip Technology Inc. MCP6546/6R/6U/7/8/9 Symbol OUT, OUTA Digital Output (comparator ...
Page 14
... MCP6546/6R/6U/7/8/9 4.0 APPLICATIONS INFORMATION The MCP6546/6R/6U/7/8/9 family of push-pull output comparators are fabricated on Microchip’s state-of-the- art CMOS process. They are suitable for a wide range of applications requiring very low power consumption. 4.1 Comparator Inputs 4.1.1 PHASE REVERSAL The MCP6546/6R/6U/7/8/9 comparator family uses CMOS transistors at the input ...
Page 15
... Time (100 ms/div) FIGURE 4-3: The MCP6546/6R/6U/7/8/9 comparators’ internal hysteresis eliminates output chatter caused by input noise voltage. 4.2 Open-Drain Output The open-drain output is designed to make level- shifting and wired-OR logic easy to implement. The output can go as high as 10V for 9V battery-powered applications ...
Page 16
... Under low-humidity conditions, a typical resistance between nearby traces is 10 would cause current to flow. This is greater than the MCP6546/6R/6U/7/8/9 family’s bias current at 25°C (1 pA, typ.). The easiest way to reduce surface leakage is to use a guard ring around sensitive pins (or traces). The guard ring is biased at the same voltage as the sensitive pin ...
Page 17
... Figure 4-10 shows one approach to designing a windowed comparator. The wired-OR connection produces a high output (logic 1) when the input voltage is between V and FIGURE 4-10: Figure 4-9 shows MCP6546 2 OUT V REF Precise Inverting (where V > 1/2 MCP6547 OUT 1/2 MCP6547 Windowed Comparator. DS21714F-page 17 ...
Page 18
... PACKAGING INFORMATION 5.1 Package Marking Information 5-Lead SC-70 (MCP6546) Device XXNN (Front) MCP6546 YWW (Back) Note 1: 2: 5-Lead SOT-23 (MCP6546, MCP6546R, MCP6546U) XXNN 8-Lead PDIP (300 mil) XXXXXXXX XXXXXNNN YYWW 8-Lead SOIC (150 mil) XXXXXXXX XXXXYYWW NNN 8-Lead MSOP XXXXXX YWWNNN Legend: XX ...
Page 19
... Package Marking Information (Continued) 14-Lead PDIP (300 mil) (MCP6549) XXXXXXXXXXXXXX XXXXXXXXXXXXXX YYWWNNN 14-Lead SOIC (150 mil) (MCP6549) XXXXXXXXXX XXXXXXXXXX YYWWNNN 14-Lead TSSOP (MCP6549) XXXXXXXX YYWW NNN © 2007 Microchip Technology Inc. MCP6546/6R/6U/7/8/9 Example: MCP6549-I/P 0729256 MCP6549-E 0729256 MCP6549 I/P 0729256 Example: ...
Page 20
... MCP6546/6R/6U/7/8/9 5-Lead Plastic Small Outline Transistor (LT) [SC70] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging Number of Pins Pitch Overall Height Molded Package Thickness Standoff Overall Width Molded Package Width Overall Length Foot Length ...
Page 21
... Lead Width Notes: 1. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.127 mm per side. 2. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. © 2007 Microchip Technology Inc. MCP6546/6R/6U/7/8 ...
Page 22
... MCP6546/6R/6U/7/8/9 8-Lead Plastic Dual In-Line (P) – 300 mil Body [PDIP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging N NOTE Number of Pins Pitch Top to Seating Plane Molded Package Thickness Base to Seating Plane Shoulder to Shoulder Width ...
Page 23
... Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15 mm per side. 4. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. © 2007 Microchip Technology Inc. MCP6546/6R/6U/7/8 ...
Page 24
... MCP6546/6R/6U/7/8/9 8-Lead Plastic Micro Small Outline Package (MS) [MSOP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging D N NOTE Number of Pins Pitch Overall Height Molded Package Thickness Standoff Overall Width Molded Package Width Overall Length ...
Page 25
... Significant Characteristic. 3. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" per side. 4. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. © 2007 Microchip Technology Inc. MCP6546/6R/6U/7/8 ...
Page 26
... MCP6546/6R/6U/7/8/9 14-Lead Plastic Small Outline (SL) – Narrow, 3.90 mm Body [SOIC] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging N NOTE Number of Pins Pitch Overall Height Molded Package Thickness Standoff § Overall Width Molded Package Width ...
Page 27
... Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15 mm per side. 3. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. © 2007 Microchip Technology Inc. MCP6546/6R/6U/7/8 ...
Page 28
... MCP6546/6R/6U/7/8/9 NOTES: DS21714F-page 28 © 2007 Microchip Technology Inc. ...
Page 29
... APPENDIX A: REVISION HISTORY Revision F (September 2007) The following is the list of modifications: 1. Corrected polarity of MCP6546U SOT-23-5 pin out diagram on front page. 2. Section 5.1 “Package Marking Information”: Updated package outline drawings per marcom. Revision E (September 2006) The following is the list of modifications: 1. Added MCP6546U pinout for the SOT-23-5 package ...
Page 30
... MCP6546/6R/6U/7/8/9 NOTES: DS21714F-page 30 © 2007 Microchip Technology Inc. ...
Page 31
... MCP6546/6R/6U/7/8/9 . Examples: a) MCP6546T-I/LT: Tape and Reel, Industrial Temperature, 5LD SC-70. b) MCP6546T-I/OT: Tape and Reel, Industrial Temperature, 5LD SOT-23. c) MCP6546-E/P: Extended Temperature, 8LD PDIP. d) MCP6546RT-I/OT: Tape and Reel, Industrial Temperature, 5LD SOT23. e) MCP6546-E/SN: Extended Temperature, 8LD SOIC. f) MCP6546UT-E/OT:Tape and Reel, Extended Temperature, 5LD SOT23 ...
Page 32
... NOTES: © 2007 Microchip Technology Inc. MCP6546/6R/6U/7/8/9 DS21714F-page 32 ...
Page 33
... PowerInfo, PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Smart Serial, SmartTel, Total Endurance, UNI/O, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...
Page 34
... Fax: 886-3-572-6459 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 © 2007 Microchip Technology Inc. EUROPE Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 France - Paris Tel: 33-1-69-53-63-20 ...