5-864839-1

Manufacturer Part Number5-864839-1
ManufacturerTE Connectivity
5-864839-1 datasheet
 


Specifications of 5-864839-1

Product TypeFlying Lead AssemblyProduct StyleCable Assembly
ShapeCircularPrewiredYes
Mount AngleStraightWire Size (mm² [awg])0.5-0.6² [20]
FlangeWithoutOperating Voltage (kvdc)15
ShieldedNoNumber Of Positions7
Mount TypeFree HangingBootWithout
Lead Assembly TypeConnector with flying leads.Assembly Length (mm [in])508.00 [20.000]
Wire ColorWhiteWire InsulationSilicone
Connector StylePlugHousing MaterialEpoxy
Rohs/elv ComplianceRoHS compliant, ELV compliantLead Free Solder ProcessesNot relevant for lead free process
Rohs/elv Compliance HistoryAlways was RoHS compliant  
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
Page 1/6

Download datasheet (271Kb)Embed
Next
Design
Objectives
Standard LGH Connectors,
Series 1/2I, 1/2LI, 1I, 1LI, 2I, 3I and 4I
DESIGN OBJECTIVES
The product described in this document has not been fully tested to ensure conformance to the requirements outlined below. Therefore
Tyco Electronics makes no representation or warranty, express or implied, that the product will comply with these requirements. Further,
Tyco Electronics may change these requirements based on the results of additional testing and evaluation. Contact Tyco Electronics
Engineering for further details.
1.
SCOPE
1.1.
Content
This specification covers perform ance, tests and quality requirem ents for the Tyco Electronics LGH
standard high voltage 1/2I, 1/2LI, 1I, 1LI, 2I, 3I and 4I series m olded end leads and receptacles. These
leads and receptacles are designed for com m ercial, industrial and m ilitary type applications requiring
operation over wide environm ents.
1.2.
Qualification
W hen tests are perform ed on the subject product line, procedures specified in Figure 1 shall be used.
All inspections shall be perform ed using the applicable inspection plan and product drawing.
2.
APPLICABLE DOCUM ENTS
The following docum ents form a part of this specification to the extent specified herein. Unless
otherwise specified, the latest edition of the docum ent applies. In the event of conflict between the
requirem ents of this specification and the product drawing, the product drawing shall take precedence.
In the event of conflict between the requirem ents of this specification and the referenced docum ents,
this specification shall take precedence.
2.1.
Tyco Electronics Docum ents
!
109 Series: Test Specifications as indicated in Figure 1
!
109-197: Test Specification (AMP Test Specifications vs EIA and IEC Test Methods)
!
114-
: Application Specification
!
501-
: Qualification Test Report
2.2.
Com m ercial Standard
EIA-364:
Electrical Connector/Socket Test Procedures Including Environm ental Classifications
2.3.
Military Standard
MIL-STD-202: Test Methods For Electronic And Electrical Com ponent Parts
3.
REQUIREM ENTS
3.1.
Design and Construction
PRELIMINARY
Product shall be of the design, construction and physical dim ensions specified on the applicable product
drawing.
©2011 Tyco Electronics Corporation,
| Indicates change
a TE Connectivity Ltd. Company
*Trademark
All Rights Reserved
TE logo is a trademark.
For latest revision, visit our website at www.te.com/documents.
For Regional Customer Service, visit our website at www.te.com
Other products, logos, and company names might be trademarks of their respective owners.
108-36033
Rev O2
1 of 6
LOC B

5-864839-1 Summary of contents

  • Page 1

    ... Series: Test Specifications as indicated in Figure 1 ! 109-197: Test Specification (AMP Test Specifications vs EIA and IEC Test Methods) ! 114- : Application Specification ! 501- : Qualification Test Report 2.2. Com m ercial Standard EIA-364: Electrical Connector/Socket Test Procedures Including Environm ental Classifications 2.3. Military Standard MIL-STD-202: Test Methods For Electronic And Electrical Com ponent Parts 3 ...

  • Page 2

    ... Figure 1 (cont) 108-36033 Procedure EIA-364-18. Visual and dim ensional ( inspection per product drawing. EIA-364-18. Visual inspection. EIA-364-6. Measure potential drop of m ated specim ens pere m axim um . ...

  • Page 3

    ... See Note. See Note. Figure 1 (cont) 108-36033 Procedure EIA-364-28, Test Condition I. Subject m ated specim ens to 10-55 traversed inute with 1 [.06 in] m axim um total excursion. 2 hours in each utually perpendicular planes. EIA-364-27, Method H. Subject m ated specim ens to 30 G's half-sine shock pulses illiseconds duration ...

  • Page 4

    ... Rev O2 Requirem ent See Note. -8 Leakage rate less than He/sec. See Note. Figure 1 (end) Test or Exam ination Test Sequence (b) 3,11,15 Figure 2 108-36033 Procedure MIL-STD 202, Method 105C, Condition C. MIL-STD 202, Method 112C, Condition C. Test Group (a) 1 2(c) 1,19 1,18 4,8 5 4,13, ...

  • Page 5

    ... Quality Conform ance Inspection The applicable quality inspection plan shall specify the sam pling acceptable quality level to be used. Dim ensional and functional requirem ents shall be in accordance with the applicable product drawing and this specification. Rev O2 108-36033 ...

  • Page 6

    ... Gage Num ber 1 2 (a) Contact: Size 16 NOTE (b) Material: Tungsten carbide Rev O2 Figure 3 Contact Resistance Measurem ent Points A Dim ension .0165 +.0001/-.0000 .0635 +.0000/-.0001 Figure 4 Engaging & Separating Gage 108-36033 B Dim ension Maxim um flat .015 ...