LT1016IS8 Linear Technology, LT1016IS8 Datasheet
LT1016IS8
Specifications of LT1016IS8
Available stocks
Related parts for LT1016IS8
LT1016IS8 Summary of contents
Page 1
... Fast Pulse Height/Width Discriminators ■ Zero-Crossing Detectors ■ Current Sense for Switching Regulators ■ High Speed Triggers ■ Crystal Oscillators , LTC and LT are registered trademarks of Linear Technology Corporation. UltraFast is a trademark of Linear Technology Corporation. U TYPICAL APPLICATION 10MHz to 25MHz Crystal Oscillator 5V 10MHz TO 25MHz 2k (AT CUT) 22Ω ...
Page 2
... Lead Temperature (Soldering, 10 sec).................. 300∞ ORDER PART NUMBER TOP VIEW + LT1016CN8 V 1 LT1016IN8 + +IN 2 – IN – 3 – PACKAGE 8-LEAD PLASTIC SO = 110∞ JMAX ORDER PART NUMBER 8 Q OUT LT1016CS8 7 Q OUT LT1016IS8 GND 6 5 LATCH S8 PART ENABLE MARKING = 120∞C/W 1016 JA 1016I ...
Page 3
ELECTRICAL CHARACTERISTICS temperature range, otherwise specifications are at T SYMBOL PARAMETER V Input Offset Voltage OS DV Input Offset Voltage Drift Input Offset Current OS I Input Bias Current B Input Voltage Range CMRR Common Mode Rejection ...
Page 4
LT1016 W U TYPICAL PERFOR A CE CHARACTERISTICS Gain Characteristics 5.0 = ± 4 OUT T = 125°C J 4.0 3.5 3 25°C J 2.5 2.0 1 – 55°C 1.0 ...
Page 5
W U TYPICAL PERFOR A CE CHARACTERISTICS Negative Supply Current vs Temperature 6 = ± OUT 100 125 –50 – JUNCTION TEMPERATURE (°C) 1016 ...
Page 6
LT1016 U U APPLICATIO S I FOR ATIO Common Mode Considerations The LT1016 is specified for a common mode range of –3.75V to 3.5V with supply voltages of ±5V. A more general consideration is that the common mode range is ...
Page 7
U U APPLICATIO S I FOR ATIO The circuit shown in Figure 1 is the best electronic means of generating a known fast, clean step to test comparators. It uses a very fast transistor in a common base configura- tion. ...
Page 8
LT1016 U U APPLICATIO S I FOR ATIO Other common problems include different measurement results using various pieces of test equipment, inability to make measurement connections to the circuit without inducing spurious responses and dissimilar operation between two “identical” circuits. ...
Page 9
U U APPLICATIO S I FOR ATIO In Figure 4 the LT1016’s supplies are bypassed, but it still oscillates. In this case, the bypass units are either too far from the device or are lossy capacitors. Use capacitors with good ...
Page 10
LT1016 U U APPLICATIO S I FOR ATIO In Figure 7 the probes are properly selected and applied but the LT1016’s output rings and distorts badly. In this case, the probe ground lead is too long. For general purpose work ...
Page 11
U U APPLICATIO S I FOR ATIO “Fuzz” on the edges is the difficulty in Figure 10. This condition appears similar to Figure 10, but the oscillation is more stubborn and persists well after the output has gone low. This ...
Page 12
LT1016 U U APPLICATIO S I FOR ATIO Another output-caused fault is shown in Figure 13. The output transitions are initially correct but end in a ringing condition. The key to the solution here is the ringing. What is happening ...
Page 13
U U APPLICATIO S I FOR ATIO 1.8ms, 12-Bit A/D Converter The LT1016’s high speed is used to implement a very fast 12-bit A/D converter in Figure 15. The circuit is a modified form of the standard successive approximation approach ...
Page 14
LT1016 U TYPICAL APPLICATIO S Voltage Controlled Pulse Width Generator 5V FULL-SCALE LM385 CALIBRATION 1.23V 500Ω 2N3906 1k 25Ω 2N3906 100pF 1000pF 5V 2. LT1016 – 2. –5V 1k 1N914 2N3906 470pF ...
Page 15
U TYPICAL APPLICATIO S 1MHz to 10MHz Crystal Oscillator 5V 1MHz TO 10MHz 2k CRYSTAL LT1016 2k OUTPUT – Q GND LATCH – 0.068µF 1016 AI04 U APPE DIX A About Level Shifts ...
Page 16
LT1016 U APPE DIX A +V OUTPUT = 0V TO TYPICALLY LT1016 OUTPUT Figure A1 + INPUT LT1016 – INVERTING VOLTAGE GAIN—BIPOLAR SWING t = 3ns RISE t = 3ns FALL TRACE A 2V/DIV TRACE B 10V/DIV ...
Page 17
PLIFIED SCHE ATIC LT1016 17 ...
Page 18
LT1016 PACKAGE DESCRIPTIO 0.300 – 0.325 (7.620 – 8.255) 0.009 – 0.015 (0.229 – 0.381) +0.035 0.325 –0.015 ( +0.889 8.255 –0.381 *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH ...
Page 19
... FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. ...
Page 20
... Comparator, Ground-Sensing Rail-to-Rail Inputs and Outputs www.linear-tech.com 5V REF 15V 15V –15V + A4 A3 470Ω LT1010 LT1006 – 6.8Ω 100k* 100k* 2.2M 20k 10MHz TRIM sn1016 1016fcs LT/TP 0601 1.5K REV C • PRINTED IN USA „ LINEAR TECHNOLOGY CORPORATION 1991 LM134 LT1034-1.2V LT1034-2.5V 1016 F16 ...