STM32F105V8 STMicroelectronics, STM32F105V8 Datasheet - Page 47

no-image

STM32F105V8

Manufacturer Part Number
STM32F105V8
Description
Mainstream Connectivity line, ARM Cortex-M3 MCU with 64 Kbytes Flash, 72 MHz CPU, CAN, USB 2.0 OTG
Manufacturer
STMicroelectronics
Datasheet

Specifications of STM32F105V8

Core
ARM 32-bit Cortex™-M3 CPU
Conversion Range
0 to 3.6 V
Dma
12-channel DMA controller
Supported Peripherals
timers, ADCs, DAC, I2Ss, SPIs, I2Cs and USARTs
Systick Timer
a 24-bit downcounter
10/100 Ethernet Mac With Dedicated Dma And Sram (4 Kbytes)
IEEE1588 hardware support, MII/RMII available on all packages

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
STM32F105V8T6
Manufacturer:
AMIC
Quantity:
101
Part Number:
STM32F105V8T6
Manufacturer:
STMicroelectronics
Quantity:
10 000
Part Number:
STM32F105V8T6
Manufacturer:
ST
0
STM32F105xx, STM32F107xx
Table 22.
1. Resonator characteristics given by the crystal/ceramic resonator manufacturer.
2. Based on characterization, not tested in production.
3. The relatively low value of the RF resistor offers a good protection against issues resulting from use in a
4. t
For C
5 pF to 25 pF range (typ.), designed for high-frequency applications, and selected to match
the requirements of the crystal or resonator (see
same size. The crystal manufacturer typically specifies a load capacitance which is the
series combination of C
can be used as a rough estimate of the combined pin and board capacitance) when sizing
C
microcontrollers” available from the ST website www.st.com.
Figure 16. Typical application with an 8 MHz crystal
1. R
Low-speed external clock generated from a crystal/ceramic resonator
The low-speed external (LSE) clock can be supplied with a 32.768 kHz crystal/ceramic
resonator oscillator. All the information given in this paragraph are based on characterization
results obtained with typical external components specified in
the resonator and the load capacitors have to be placed as close as possible to the oscillator
pins in order to minimize output distortion and startup stabilization time. Refer to the crystal
t
SU(HSE
Symbol
L1
f
OSC_IN
humid environment, due to the induced leakage and the bias condition change. However, it is
recommended to take this point into account if the MCU is used in tough humidity conditions.
oscillation is reached. This value is measured for a standard crystal resonator and it can vary significantly
with the crystal manufacturer
Resonator with
integrated capacitors
SU(HSE)
R
g
and C
C
EXT
i
2
m
F
L1
(4)
value depends on the crystal characteristics.
and C
is the startup time measured from the moment it is enabled (by software) to a stabilized 8 MHz
L2
Oscillator frequency
Feedback resistor
Recommended load capacitance
versus equivalent serial
resistance of the crystal (R
HSE driving current
Oscillator transconductance
Startup time
. Refer to the application note AN2867 “Oscillator design guide for ST
HSE 3-25 MHz oscillator characteristics
L2
C L2
, it is recommended to use high-quality external ceramic capacitors in the
C L1
Parameter
L1
8 MH z
resonator
R EXT (1)
and C
Doc ID 15274 Rev 6
L2
. PCB and MCU pin capacitance must be included (10 pF
OSC_OU T
OSC_IN
S
)
(3)
V
R F
DD
V
with 30 pF load
= 3.3 V, V
DD
Conditions
controlled
R
Figure
Startup
Bias
S
is stabilized
gain
= 30 Ω
(1) (2)
IN
16). C
= V
SS
STM32F10xxx
Table
L1
Electrical characteristics
and C
f HSE
Min
25
3
23. In the application,
L2
Typ
200
30
2
are usually the
Max
25
1
ai14128b
mA/V
47/104
MHz
Unit
mA
ms
pF

Related parts for STM32F105V8