STM32F103ZC STMicroelectronics, STM32F103ZC Datasheet - Page 23

no-image

STM32F103ZC

Manufacturer Part Number
STM32F103ZC
Description
Mainstream Performance line, ARM Cortex-M3 MCU with 256 Kbytes Flash, 72 MHz CPU, motor control, USB and CAN
Manufacturer
STMicroelectronics
Datasheet

Specifications of STM32F103ZC

Core
ARM 32-bit Cortex™-M3 CPU
Conversion Range
0 to 3.6 V
Dma
12-channel DMA controller
Supported Peripherals
timers, ADCs, DAC, SDIO, I2Ss, SPIs, I2Cs and USARTs
Systick Timer
a 24-bit downcounter

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
STM32F103ZC
Manufacturer:
ST
0
Part Number:
STM32F103ZCH6
Manufacturer:
STMicroelectronics
Quantity:
10 000
Part Number:
STM32F103ZCH6
0
Part Number:
STM32F103ZCH6.
Manufacturer:
ST
0
Part Number:
STM32F103ZCT
Manufacturer:
ST
0
Part Number:
STM32F103ZCT6
Manufacturer:
STMicroelectronics
Quantity:
20 000
Part Number:
STM32F103ZCT6
Manufacturer:
STMicroelectronics
Quantity:
10 000
Part Number:
STM32F103ZCT6
Manufacturer:
ST
Quantity:
200
Part Number:
STM32F103ZCT6
Manufacturer:
ST
Quantity:
20 000
Part Number:
STM32F103ZCT6
0
STM32F103xC, STM32F103xD, STM32F103xE
2.3.28
2.3.29
2.3.30
This dual digital Interface supports the following features:
Eight DAC trigger inputs are used in the STM32F103xC, STM32F103xD and
STM32F103xE performance line family. The DAC channels are triggered through the timer
update outputs that are also connected to different DMA channels.
Temperature sensor
The temperature sensor has to generate a voltage that varies linearly with temperature. The
conversion range is between 2 V < V
connected to the ADC1_IN16 input channel which is used to convert the sensor output
voltage into a digital value.
Serial wire JTAG debug port (SWJ-DP)
The ARM SWJ-DP Interface is embedded, and is a combined JTAG and serial wire debug
port that enables either a serial wire debug or a JTAG probe to be connected to the target.
The JTAG TMS and TCK pins are shared respectively with SWDIO and SWCLK and a
specific sequence on the TMS pin is used to switch between JTAG-DP and SW-DP.
Embedded Trace Macrocell™
The ARM
data flow inside the CPU core by streaming compressed data at a very high rate from the
STM32F10xxx through a small number of ETM pins to an external hardware trace port
analyzer (TPA) device. The TPA is connected to a host computer using USB, Ethernet, or
any other high-speed channel. Real-time instruction and data flow activity can be recorded
and then formatted for display on the host computer running debugger software. TPA
hardware is commercially available from common development tool vendors. It operates
with third party debugger software tools.
two DAC converters: one for each output channel
8-bit or 12-bit monotonic output
left or right data alignment in 12-bit mode
synchronized update capability
noise-wave generation
triangular-wave generation
dual DAC channel independent or simultaneous conversions
DMA capability for each channel
external triggers for conversion
input voltage reference V
®
Embedded Trace Macrocell provides a greater visibility of the instruction and
REF+
Doc ID 14611 Rev 8
DDA
< 3.6 V. The temperature sensor is internally
Description
23/130

Related parts for STM32F103ZC