STM32F103ZC

Manufacturer Part NumberSTM32F103ZC
DescriptionMainstream Performance line, ARM Cortex-M3 MCU with 256 Kbytes Flash, 72 MHz CPU, motor control, USB and CAN
ManufacturerSTMicroelectronics
STM32F103ZC datasheet
 

Specifications of STM32F103ZC

CoreARM 32-bit Cortex™-M3 CPUConversion Range0 to 3.6 V
Dma12-channel DMA controllerSupported Peripheralstimers, ADCs, DAC, SDIO, I2Ss, SPIs, I2Cs and USARTs
Systick Timera 24-bit downcounter  
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Page 41
42
Page 42
43
Page 43
44
Page 44
45
Page 45
46
Page 46
47
Page 47
48
Page 48
49
Page 49
50
Page 50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
Page 44/130

Download datasheet (2Mb)Embed
PrevNext
Electrical characteristics
5.3.4
Embedded reference voltage
The parameters given in
temperature and V
Table 13.
Embedded internal reference voltage
Symbol
V
Internal reference voltage
REFINT
ADC sampling time when
(1)
T
reading the internal reference
S_vrefint
voltage
Internal reference voltage
(2)
V
spread over the temperature
RERINT
range
(2)
T
Temperature coefficient
Coeff
1. Shortest sampling time can be determined in the application by multiple iterations.
2. Guaranteed by design, not tested in production.
5.3.5
Supply current characteristics
The current consumption is a function of several parameters and factors such as the
operating voltage, ambient temperature, I/O pin loading, device software configuration,
operating frequencies, I/O pin switching rate, program location in memory and executed
binary code.
The current consumption is measured as described in
measurement
scheme.
All Run-mode current consumption measurements given in this section are performed with a
reduced code that gives a consumption equivalent to Dhrystone 2.1 code.
Maximum current consumption
The MCU is placed under the following conditions:
All I/O pins are in input mode with a static value at V
All peripherals are disabled except when explicitly mentioned
The Flash memory access time is adjusted to the f
to 24 MHz, 1 wait state from 24 to 48 MHz and 2 wait states above)
Prefetch in ON (reminder: this bit must be set before clock setting and bus prescaling)
When the peripherals are enabled f
The parameters given in
under ambient temperature and V
44/130
STM32F103xC, STM32F103xD, STM32F103xE
Table 13
are derived from tests performed under ambient
supply voltage conditions summarized in
DD
Parameter
Conditions
–40 °C < T
–40 °C < T
V
= 3 V ±10 mV
DD
= f
PCLK1
Table
14,
Table 15
and
Table 16
supply voltage conditions summarized in
DD
Doc ID 14611 Rev 8
Table
10.
Min
Max
Typ
< +105 °C
1.16 1.20
1.26
A
< +85 °C
1.16 1.20
1.24
A
5.1
17.1
10
100
Figure 13: Current consumption
or V
(no load)
DD
SS
frequency (0 wait state from 0
HCLK
/2, f
= f
HCLK
PCLK2
HCLK
are derived from tests performed
Table
Unit
V
V
(2)
µs
mV
ppm/°C
10.