MAX4162 Maxim, MAX4162 Datasheet
MAX4162
Available stocks
Related parts for MAX4162
MAX4162 Summary of contents
Page 1
... They consume a mere 25µA quiescent current per amplifier, yet achieve 200kHz gain-bandwidth product and are unity-gain stable while driving any capacitive load. The MAX4162/ MAX4163/MAX4164 operate from either a single supply (2.5V to 10V) or dual supplies (±1.25V to ±5V), with an input common-mode voltage range that extends 250mV beyond either supply rail ...
Page 2
... Junction Temperature ......................................................+150°C Lead Temperature (soldering, 10s) .................................+300°C Soldering Temperature (reflow, UCSP)............................+260° /2, R connected CONDITIONS Inferred from PSRR test T = +25°C A MAX4162 T = -40°C to +85° +25°C A MAX4163 T = -40°C to +85° +25°C A MAX4164 T = -40° ...
Page 3
... CONDITIONS f = 1kHz /2, R connected CONDITIONS Inferred from PSRR test T = +25°C A MAX4162 T = -40°C to +85° +25°C A MAX4163 T = -40°C to +85° +25°C A MAX4164 T = -40°C to +85°C A Inferred from CMRR test ...
Page 4
UCSP, Micropower, Single-Supply, 10V, Rail-to-Rail I/O Op Amps ELECTRICAL CHARACTERISTICS: 5V Operation (continued OUT values are +25°C.) (Note 1) A PARAMETER SYMBOL ...
Page 5
UCSP, Micropower, Single-Supply, 10V +25°C, unless otherwise noted INPUT OFFSET VOLTAGE vs. TEMPERATURE 1000 750 500 250 0 -250 -500 -750 -1000 -40 ...
Page 6
... -40 - TEMPERATURE (°C) NOISE VOLTAGE DENSITY vs. FREQUENCY 100 5.5 10 100 1k 10k 100k FREQUENCY (Hz) MAXIMUM OUTPUT VOLTAGE vs. TEMPERATURE (V = 5V) DD 100 LOAD 1.6 2.0 -40 -20 ...
Page 7
... GAIN AND PHASE vs. FREQUENCY (C = 0.01µF) L MAX4162-24 180 R = 100kΩ L 144 C = 0.01µF L GAIN A = 1000 108 -36 -72 -108 PHASE -144 -180 1 100 1k 10k 100k 1M FREQUENCY (Hz) NONINVERTING SMALL-SIGNAL PULSE RESPONSE ( 1500pF MAX4162-26 IN 100µs/div = 3V 100mV 100kΩ / 1500pF L 7 ...
Page 8
... C DD MAX4162-28 IN 1V/div OUT 1V/div 100µs/div / 3V 2V NONINVERTING LARGE-SIGNAL PULSE RESPONSE ( MAX4162-31 IN 100µs/div 100kΩ / MAX4162-29 = 100kΩ /2, DD ...
Page 9
... Rail-to-Rail I/O Op Amps Typical Operating Characteristics (continued 1500pF) L MAX4162-32 0 -20 -40 -60 -80 -100 -120 -140 -160 100µs/div = 100kΩ / MAX4164 NAME UCSP SO — ...
Page 10
... An internal charge pump provides two internal supplies typically 2V beyond each rail. These internal rails allow the MAX4162/MAX4163/MAX4164 to achieve true rail- to-rail inputs and outputs, while providing excellent common-mode rejection, power-supply rejection ratios, and gain linearity. ...
Page 11
... The charge pumps typically require up to 20µs on power-up to fully energize the internal supply rails (Figure 3). Power Supplies and Layout The MAX4162/MAX4163/MAX4164 are guaranteed to operate from a single 2.5V to 10.0V power supply, but full rail-to-rail operation typically extends below 2V. For single-supply operation, bypass the power supply with a 1µ ...
Page 12
... RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE SOT23 8 UCSP 8 µMAX 14 SO POWER-UP TRANSIENT (V = 5V) DD MAX4162- 2V/div 0 2.5V OUT 1V/div 0 100µs/div 10kΩ ...
Page 13
... Information, and added UCSP soldering temperature Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 13 © ...