MAX4294 Maxim, MAX4294 Datasheet
MAX4294
Available stocks
Related parts for MAX4294
MAX4294 Summary of contents
Page 1
... The MAX4291/MAX4292/MAX4294 have an input com- mon-mode range that extends to each supply rail, and their outputs swing to within 46mV of the rails with a 2k load. Although the minimum operating voltage is speci- fied at 1 ...
Page 2
... < 10mV IN+ IN- Inferred from CMRR test Tested for MAX4291 1.8V; MAX4292/MAX4294 V = 1.8V CC Tested for MAX4291 5.0V, MAX4292/MAX4294 V = 5. +25°C, unless otherwise noted MIN TYP MAX UNITS 1.8 5.5 V 100 210 µA 100 255 ±400 ±2500 µV ±200 ±1200 ±15 ± ...
Page 3
... 100k to V Specified Sourcing or sinking Specified 10kHz (MAX4292/MAX4294 only) ISO 10kHz 10kHz 1V/V, no sustained oscillations VCL = V / 100k connected to V OUT CC L CONDITIONS Inferred from PSRR test 1.8V ...
Page 4
... CONDITIONS 5.0V 5. 5.0V 5. Inferred from CMRR test Tested for MAX4291 0 V 1.8V 1.8V MAX4292/MAX4294 CC Tested for MAX4291 0 V 5.0V, CM MAX4292/MAX4294 100k , L 0.02V V V OUT 1. 0. OUT 100k , L 0.02V V V OUT 5.0V ...
Page 5
OUT CC SUPPLY CURRENT PER AMPLIFIER vs. TEMPERATURE 160 150 140 130 V = 5.5V CC 120 110 100 1. ...
Page 6
... CC L 130 120 110 100 100 150 200 250 300 350 400 450 500 V (mV) OL MAX4292/MAX4294 CROSSTALK vs. FREQUENCY 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 0.01 0 FREQUENCY (kHz) TOTAL HARMONIC DISTORTION PLUS NOISE vs. FREQUENCY 180 144 ...
Page 7
OUT CC LOAD RESISTOR vs. CAPACITIVE LOAD 100 10% OVERSHOOT A = 1V/V V (NONINVERTING CONFIGURATION 5. 2.4V CC ...
Page 8
... The crossover region of these two pairs occurs halfway between V and V CC voltage is typically ±200µV (MAX4292/MAX4294). Low operating supply voltage, low supply current, rail-to-rail common-mode input range, and rail-to-rail outputs make this family of operational amplifiers (op amps) an excellent choice for precision or general-purpose, low- voltage, battery-powered systems ...
Page 9
... A high power-supply rejection ratio of 100dB allows the amplifiers to be powered directly off a decaying battery voltage, simplifying design and extending battery life. The MAX4291/MAX4292/MAX4294 are ideally suited for use with most battery-powered systems. Table 1 lists a MAX4291 CAPACITY, AA SIZE OPERATING TIME IN ...
Page 10
... Figures 6a and 6b show the typical current source and sink capabilities of the MAX4291/MAX4292/MAX4294 family as a function of supply voltage and ambient tem- perature. The contours on the graph depict the output current value, based on driving the output voltage to within 50mV, 100mV, and 200mV of either power-sup- ply rail ...
Page 11
... Using the MAX4291/MAX4292/MAX4294 Although optimized for use as operational amplifiers, the MAX4291/MAX4292/MAX4294 can also be used as load resistor rail-to-rail I/O comparators. Typical propagation delay depends on the input overdrive voltage, as shown in Figure 8. External hysteresis can be used to minimize the risk of output oscillation. The positive feedback cir- cuit, shown in Figure 9, causes the input threshold to change when the output voltage changes state ...
Page 12
... CC Using the MAX4291/MAX4292/MAX4294 as Low-Power Current Monitors The MAX4291/MAX4292/MAX4294 are ideal for appli- cations powered from a two-cell battery stack. Figure 11 shows an application circuit in which the MAX4291 is used for monitoring the current of a two-cell battery stack. In this circuit, a current load is applied, and the voltage drop at the battery terminal is sensed ...
Page 13
For a 1V output and a current load of 50mA, the choice of resistors can 100k , and UCSP Information Design the layout for the ...
Page 14
... Ultra-Small, 1.8V, µPower, Rail-to-Rail I/O Op Amps TOP VIEW IN+ 1 MAX4291 IN- SC70/SOT23 Chip Information MAX4291 TRANSISTOR COUNT: 149 MAX4292 TRANSISTOR COUNT: 356 MAX4294 TRANSISTOR COUNT: 747 PROCESS: BiCMOS 14 ______________________________________________________________________________________ Pin Configurations (continued) V OUTA OUTB INA- MAX4292 3 6 INB- ...
Page 15
... For the latest package outline information www.maxim-ic.com/packages.) ______________________________________________________________________________________ Ultra-Small, 1.8V, µPower, Rail-to-Rail I/O Op Amps Package Information 15 ...
Page 16
... E ÿ 0.50±0.1 0.6±0.1 1 0.6±0.1 D TOP VIEW FRONT VIEW Note: The MAX4292 does not have an exposed pad. Note: The MAX4294 does not have an exposed pad. 16 ______________________________________________________________________________________ Package Information (continued INCHES DIM MIN 0.002 A2 0.030 b 0 ...
Page 17
... For the latest package outline information www.maxim-ic.com/packages.) ______________________________________________________________________________________ Ultra-Small, 1.8V, µPower, Rail-to-Rail I/O Op Amps Package Information (continued) 17 ...
Page 18
... For the latest package outline information www.maxim-ic.com/packages.) Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. ...