MAX4488 Maxim, MAX4488 Datasheet
MAX4488
Available stocks
Related parts for MAX4488
MAX4488 Summary of contents
Page 1
... These features make the devices an ideal choice for applications that require low distortion and/or low noise. For power conservation, the MAX4475/MAX4488 offer a low-power shutdown mode that reduces supply current to 0.01µA and places the amplifiers’ outputs into a high- impedance state. These amplifiers have outputs which swing rail-to-rail and their input common-mode voltage range includes ground. The MAX4475– ...
Page 2
... SO (derate 5.88mW/°C above +70°C)...............471mW Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability ...
Page 3
... R = 10kΩ to GND OUT P 1kHz A = +1V/V V (MAX4475–MAX4478 20kHz R = 1kΩ to GND OUT P 1kHz A = +5V/V V (MAX4488/MAX4489 20kHz R = 10kΩ to GND -40°C to +125°C, unless otherwise noted. A MIN TYP MAX - 200 150 SS ...
Page 4
... Enable Delay Time from Shutdown Power-Up Delay Time Note 1: All devices are 100% tested at T Note 2: SHDN is available on the MAX4475/MAX4488 only. Note 3: Guaranteed by the PSRR test. Note 4: Guaranteed by design. Note 5: Full-power bandwidth for unity-gain stable devices (MAX4475–MAX4478) is measured in a closed-loop gain of +2V/V to accommodate the input voltage range, V Note 6: Lowpass-filter bandwidth is 22kHz for f = 1kHz and 80kHz for f = 20kHz. Noise floor of test equipment = 10nV/√ ...
Page 5
SOT23, Low-Noise, Low-Distortion + OUT measurements +25°C, unless otherwise noted.) A OUTPUT VOLTAGE vs. OUTPUT LOAD CURRENT 0. ±10mV ...
Page 6
... INPUT OFFSET VOLTAGE vs. SUPPLY VOLTAGE -10 -15 - 2.5 3.0 3.5 4.0 SUPPLY VOLTAGE (V) MAX4488/MAX4489 GAIN AND PHASE vs. FREQUENCY MAX4475 toc17 180 GAIN 144 108 -36 - -108 R = 50kΩ L PHASE C = 20pF L -144 A = +1000V/V V ...
Page 7
... 0.1Hz TO 10Hz NOISE P-P MAX4475 toc21 NOISE = 260nV P-P P-P 200nV/div 1s/div MAX4488/MAX4489 TOTAL HARMONIC DISTORTION PLUS NOISE vs. FREQUENCY 0.01 0.001 A = +10 +10, V FILTER BW = 22kHz 10kΩ TO GND 5.6kΩ ...
Page 8
... EP (TDFN EP (TDFN — only) only) 8 _______________________________________________________________________________________ Typical Operating Characteristics (continued /2, R tied to V /2, input noise floor of test equipment =10nV/√Hz for all distortion MAX4488/MAX4489 SMALL-SIGNAL PULSE RESPONSE MAX4475 toc30 1µs/div 10kΩ 50pF 20mV PULSE +5V/V IN ...
Page 9
... The MAX4475–MAX4478 are unity-gain stable, while the MAX4488/MAX4489 have a higher slew rate and are stable for gains ≥ 5V/V. The MAX4475/MAX4488 feature a low-power shutdown mode, which reduces the supply current to 0.01µA and disables the outputs. ...
Page 10
... the unity-gain stable MAX4475–MAX4478, the use of a proper C is most important for -1V/V. In the decompensated MAX4488/ V MAX4489 most important for A Z Figures 2a and 2b show transient response both with and without Using a slightly smaller C ...
Page 11
... In addition, the MAX4475 has excellent open- loop gain and common-mode rejection, making this an excellent ouput buffer amplifier. The MAX4475–MAX4478/MAX4488/MAX4489 offer a unique combination of low noise, wide bandwidth, and high gain, making them an excellent choice for active filters up to 1MHz. The Typical Operating Circuit shows the dual MAX4477 configured as a 5th order Chebyschev filter with a cutoff frequency of 100kHz ...
Page 12
... TOP VIEW OUT MAX4475 SHDN MAX4488 SS IN IN- SOT23-6 TOP VIEW N.C. 4 IN- + *EP = EXPOSED PADDLE. Pin Configurations OUTB 7 MAX4477 MAX4489 6 INB- 5 INB+ SO/µMAX MAX4475 MAX4488 * TDFN *EP = EXPOSED PADDLE MAX4476 * TDFN ...
Page 13
... MAX4478ASD+ -40°C to +125°C -40°C to +125°C MAX4488AUT+T MAX4488AUA+ -40°C to +125°C MAX4488ASA+ -40°C to +125°C MAX4488ATT+T -40°C to +125°C -40°C to +125°C MAX4489AUA+ + Denotes a lead(Pb)-free/RoHS-compliant package Exposed pad (connect denotes an automotive qualified part. ...
Page 14
... Wide-Band, Rail-to-Rail Op Amps For the latest package outline information and land patterns www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status ...
Page 15
... SOT23, Low-Noise, Low-Distortion, For the latest package outline information and land patterns www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status ...
Page 16
... Wide-Band, Rail-to-Rail Op Amps For the latest package outline information and land patterns www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status ...
Page 17
... SOT23, Low-Noise, Low-Distortion, For the latest package outline information and land patterns www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status ...
Page 18
... Wide-Band, Rail-to-Rail Op Amps For the latest package outline information and land patterns www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status ...
Page 19
... SOT23, Low-Noise, Low-Distortion, For the latest package outline information and land patterns www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status ...
Page 20
... Wide-Band, Rail-to-Rail Op Amps For the latest package outline information and land patterns www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status ...
Page 21
... Added /V designation to the MAX4475 product and soldering temperature Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. ...