MAX14509AE Maxim, MAX14509AE Datasheet
MAX14509AE
Available stocks
Related parts for MAX14509AE
MAX14509AE Summary of contents
Page 1
... The MAX14508E/MAX14509E/MAX14509AE have an enable input (EN) to reduce supply current and set all channels to high impedance when driven low. The MAX14508E–MAX14511E/MAX14509AE are avail- able in a space-saving, 10-pin, 1.4mm x 1.8mm UTQFN package, and operate over the -40°C to +85°C temper- ature range. ...
Page 2
... Continuous Power Dissipation (T = +70°C) A 10-Pin UTQFN (derate 6.9mW/°C above +70°C).........559mW Note 1: Limits are only for the MAX14508E/MAX14509E/MAX14510E/MAX14511E. For the MAX14509AE (V from (V - 5.0V) to min of 6. Note 2: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four- layer board. For detailed information on package thermal considerations, refer to www.maxim-ic.com/thermal-tutorial. Stresses beyond those listed under “ ...
Page 3
... COM_ On-Leakage Current I COM_(ON) Turn-On Time t ON (Figure 2) _______________________________________________________________________________________ with Negative Signal Capability CONDITIONS V = 3.0V -1.5V, +1.5V; CC ANO_ I = 10mA COM_ V = 3.0V 0V UNC_ CC COM_ MAX14509AE 2.7V 3.6V, CC COM_ I = 10mA COM_ V = 3.0V 0V 10mA CC ANO_ COM_ (Notes 3.0V 0V 10mA CC UNC_ COM_ (Notes 3.0V 10mA ...
Page 4
... L UNC_ f = 100kHz COM_ RMS ISO Figure 100kHz COM_ RMS CT Figure 4 (Note 8) ANO_ to COM_ 20Hz to 20kHz 0. bias = 0V, R COM_ P MAX14508E/MAX14509E/MAX14509AE +3.0V +25°C.) (Note MIN TYP MAX = 50Ω 0V 1 5.0V, ...
Page 5
... Note 4: The switch turns off for voltages above V Note 5: Guaranteed by design. Note 6: ΔR = ABS ON(MAX) ON(CH1) Note 7: Flatness is defined as the difference between the maximum and minimum value of on-resistance, as measured over specified analog signal ranges. Note 8: Between two switches. _______________________________________________________________________________________ with Negative Signal Capability CONDITIONS Human Body Model Human Body Model = +25° ...
Page 6
... USB 2.0 Hi-Speed and Audio Switches with Negative Signal Capability MAX14508E/ MAX14509E/ MAX14510E/ MAX14511E Figure 1. Fault Protection MAX14508E/ MAX14509E/ MAX14510E/ MAX14511E/ ANO_ V MAX14509AE IN_ OR UNC_ CONTROL LOGIC INPUT C INCLUDES FIXTURE AND STRAY CAPACITANCE OUT IN_ Figure 2. Switching Time ...
Page 7
... USB 2.0 Hi-Speed and Audio Switches MAX14508E/ MAX14509E/ UNC1 OR R MAX14510E/ S ANO1 MAX14511E/ V IN+ MAX14509AE UNC2 ANO2 V IN IN+ 50 50% IN PLHX OUT+ 50 50% V OUT PHLY Figure 3. Output Skew _______________________________________________________________________________________ with Negative Signal Capability ...
Page 8
... MAX14510E/ ANO1* 50Ω MAX14511E/ MAX14509AE OFF-ISOLATION IS MEASURED BETWEEN COM_ AND "OFF" ANO_ OR UNC_ TERMINAL ON EACH SWITCH. ON-LOSS IS MEASURED BETWEEN COM_ AND "ON" ANO_ OR UNC_ TERMINAL ON EACH SWITCH. CROSSTALK IS MEASURED FROM ONE CHANNEL TO THE OTHER CHANNEL. Figure 4. On-Loss, Off-Isolation, and Crosstalk ...
Page 9
USB 2.0 Hi-Speed and Audio Switches (V = 3.0V +25°C, unless otherwise noted UNC_ ON-RESISTANCE vs. V COM_ 2. 10mA UNC_ 2. 2.7V 2.50 CC 2.45 2.40 2. 5.0V CC ...
Page 10
... CC A TOTAL HARMONIC DISTORTION PLUS NOISE vs. FREQUENCY 600Ω L 0.1 0.01 0.001 0.0001 0.01 0 FREQUENCY (MHz) PIN MAX14508E/ NAME MAX14510E/ MAX14509E/ MAX14511E MAX14509AE 1 1 UNC1 2 2 ANO2 3 3 ANO1 4 4 GND COM1 7 7 COM2 8 — ...
Page 11
... USB 2.0 Hi-Speed and Audio Switches MAX14508E/MAX14509E/MAX14509AE Functional Diagrams/Truth Table UNC1 UNC2 ANO1 ANO2 EN MAX14508E/MAX14509E/MAX14509AE MAX14510E/MAX14511E Functional Diagrams/Truth Table UNC1 UNC2 ANO1 ANO2 VB > V VBDET < V VBDET Don’t Care ______________________________________________________________________________________ with Negative Signal Capability MAX14508E UNC1 COM1 UNC2 ...
Page 12
... The MAX14508E/MAX14509E/MAX14509AE provide a single-bit control logic input, CB. CB controls the switch position as shown in the MAX14508E/MAX14509E/ MAX14509AE Functional Diagrams/Truth Table . Drive CB rail-to-rail to minimize power consumption. ) necessary for high- The MAX14508E/MAX14509E/MAX14509AE feature a shutdown mode that reduces the supply current to less than 10nA and places the switches in high impedance. ...
Page 13
... C s STORAGE VOLTAGE 100pF CAPACITOR DC SOURCE Figure 5. Human Body ESD Test Model Power-Supply Sequencing Caution: Do not exceed the absolute maximum rat- ings because stresses beyond the listed ratings may cause permanent damage to the device. ______________________________________________________________________________________ with Negative Signal Capability I 100% P 90% ...
Page 14
... PROCESS: BiCMOS 14 ______________________________________________________________________________________ 3.0V 0.1μ MAX14510E/ MAX14511E MAX14510E ONLY GND AOR For the latest package outline information and land patterns www.maxim-ic.com/packages. PACKAGE TYPE 10 Ultra-Thin QFN Typical Operating Circuit COM1 COMBINATION USB AND AUDIO CONNECTOR COM2 VB V VBDET VBUS Package Information PACKAGE CODE DOCUMENT NO ...
Page 15
... Characteristics, Figure 4, and Layout section. Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 15 © ...