LMC6482

Manufacturer Part NumberLMC6482
ManufacturerTexas Instruments
LMC6482 datasheet
 


Specifications of LMC6482

Number Of Channels2Total Supply Voltage(min)(+5v=5, +/-5v=10)3
Total Supply Voltage(max)(+5v=5, +/-5v=10)15.5Iq Per Channel(max)(ma)0.7
Gbw(typ)(mhz)1.5Slew Rate(typ)(v/us)1.3
Vio (25c)(max)(mv)0.75Vn At 1khz(typ)(nv/rthz)37
Iib(max)(pa)4Rail-railIn/Out
Pin/package8PDIP, 8SOIC, 8VSSOP  
1
2
3
4
5
6
7
8
9
10
11
Page 11
12
Page 12
13
Page 13
14
Page 14
15
Page 15
16
Page 16
17
Page 17
18
Page 18
19
Page 19
20
Page 20
21
22
23
24
25
26
27
Page 15/27

Download datasheet (2Mb)Embed
PrevNext
Application Information
1.0 AMPLIFIER TOPOLOGY
The LMC6482 incorporates specially designed wide-
compliance range current mirrors and the body effect to
extend input common mode range to each supply rail.
Complementary paralleled differential input stages, like the
type used in other CMOS and bipolar rail-to-rail input ampli-
fiers, were not used because of their inherent accuracy
problems due to CMRR, cross-over distortion, and open-
loop gain variation.
The LMC6482’s input stage design is complemented by an
output stage capable of rail-to-rail output swing even when
driving a large load. Rail-to-rail output swing is obtained by
taking the output directly from the internal integrator instead
of an output buffer stage.
2.0 INPUT COMMON-MODE VOLTAGE RANGE
Unlike Bi-FET amplifier designs, the LMC6482 does not
exhibit phase inversion when an input voltage exceeds the
negative supply voltage. Figure 1 shows an input voltage
exceeding both supplies with no resulting phase inversion on
the output.
FIGURE 1. An Input Voltage Signal Exceeds the
LMC6482 Power Supply Voltages with
No Output Phase Inversion
The absolute maximum input voltage is 300mV beyond ei-
ther supply rail at room temperature. Voltages greatly ex-
ceeding this absolute maximum rating, as in Figure 2, can
cause excessive current to flow in or out of the input pins
possibly affecting reliability.
www.national.com
FIGURE 2. A
Exceeds the 3V Supply in Figure 3 Causing
No Phase Inversion Due to R
Applications that exceed this rating must externally limit the
maximum input current to
shown in Figure 3.
FIGURE 3. R
Voltages Exceeding the Supply Voltages
3.0 RAIL-TO-RAIL OUTPUT
The approximated output resistance of the LMC6482 is
180Ω sourcing and 130Ω sinking at V
01171310
sourcing and 80Ω sinking at Vs = 5V. Using the calculated
output resistance, maximum output voltage swing can be
estimated as a function of load.
4.0 CAPACITIVE LOAD TOLERANCE
The LMC6482 can typically directly drive a 100pF load with
V
= 15V at unity gain without oscillating. The unity gain
S
follower is the most sensitive configuration. Direct capacitive
loading reduces the phase margin of op-amps. The combi-
nation of the op-amp’s output impedance and the capacitive
load induces phase lag. This results in either an under-
damped pulse response or oscillation.
Capacitive load compensation can be accomplished using
resistive isolation as shown in Figure 4. This simple tech-
nique is useful for isolating the capacitive inputs of multiplex-
ers and A/D converters.
14
01171339
±
7.5V Input Signal Greatly
I
±
5mA with an input resistor (R
) as
I
01171311
Input Current Protection for
I
= 3V and 110Ω
S