The PCM9211 is a complete analog and digital front-end for today's multimedia players and recorders

PCM9211

Manufacturer Part NumberPCM9211
DescriptionThe PCM9211 is a complete analog and digital front-end for today's multimedia players and recorders
ManufacturerTexas Instruments
PCM9211 datasheet
 


Specifications of PCM9211

Jitter(ps)50Sampling Rate(max)(khz)216
Power Supply(v)4.5-5.5 for Analog ,2.9-3.6 for DIXAdc Resolution(bits)24
Adc Sample Rate (ksps)96Control ModeSPI, I2C, Hardware
InputsPCM,S/PDIF, ADCOutputPCM,S/PDIF
Operating Temperature Range(c)-40 to 85Pin/package48LQFP
1
2
3
4
5
6
7
8
9
10
11
Page 11
12
Page 12
13
Page 13
14
Page 14
15
Page 15
16
Page 16
17
Page 17
18
Page 18
19
Page 19
20
Page 20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
Page 15/121

Download datasheet (2Mb)Embed
PrevNext
www.ti.com
Auxiliary PCM Audio Input and Output (I/O)
There are up to 3x digital auxiliary (AUX) inputs and one AUX output on the PCM9211. These I/Os are
multiplexed and shared with RXIN4 through RXIN7, MPIOB, and MPIOC. Each input and output supports a
four-wire digital audio interface that is similar to the I
(bit clock), LRCK (left/right clock, or word clock) and data transmissions. The audio format supported through the
2
Aux I/O can be configured for I
S, 24-bit left-justified (LJ), 24-bit right-justified (RJ), and 16-bit RJ output.
The AUX inputs are designed to be driven in Clock Slave mode. The Aux Output can only operate in Master
mode. The system clock can be run from 128f
Routing
All 3x AUXIN data and clocks, in addition to data and clocks from the ADC and DIR modules, are routed to three
output ports. The Main Output Port and Aux Output Port (that can be output through MPIO_B) are both PCM
2
outputs capable of I
S, RJ, and LJ. The DIT output is an S/PDIF signal output.
All three outputs have individual multiplexers that can select between the AUXINs, DIR, or ADC.
Control Interface
The PCM9211 can be controlled by either SPI or I
goes into a default routing mode. Details of this mode are discussed in the
certain applications, the default configuration may be suitable, and therefore does not require external
programming.
Multipurpose I/O
The PCM9211 includes 12 MPIO (Multi-Purpose Inputs/Outputs) and two MPO (Multi-Purpose Output) pins.
These MPIO/MPO pins can be easily set to different configurations through registers to allow different routing
and provide data outputs based on the specific application.
The 12 MPIO pins are divided into three groups (A, B, and C); each group has four pins (MPIO_Ax, MPIO_Bx,
and MPIO_Cx).
For example, to access all 12 S/PDIF inputs, the MPIO_Ax pins can be configured to support S/PDIF RXIN8 and
RXIN11. However, if the application requires an additional I
for an Aux In instead of RXIN8 and RXIN11.
Copyright © 2010, Texas Instruments Incorporated
2
S protocol. Each I/O can support SCK (system clock), BCK
, 256f
, and 512f
. However, the ADC cannot run from 128f
S
S
S
2
2
C (up to a 400-kHz I
C bus). However, on startup, the device
2
S input, then the MPIO_Ax pins can be configured
Product Folder Link(s):
PCM9211
PCM9211
SBAS495 – JUNE 2010
.
S
Serial Control Mode
section. For
Submit Documentation Feedback
15