The PCM9211 is a complete analog and digital front-end for today's multimedia players and recorders

PCM9211

Manufacturer Part NumberPCM9211
DescriptionThe PCM9211 is a complete analog and digital front-end for today's multimedia players and recorders
ManufacturerTexas Instruments
PCM9211 datasheet
 


Specifications of PCM9211

Jitter(ps)50Sampling Rate(max)(khz)216
Power Supply(v)4.5-5.5 for Analog ,2.9-3.6 for DIXAdc Resolution(bits)24
Adc Sample Rate (ksps)96Control ModeSPI, I2C, Hardware
InputsPCM,S/PDIF, ADCOutputPCM,S/PDIF
Operating Temperature Range(c)-40 to 85Pin/package48LQFP
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Page 21
22
Page 22
23
Page 23
24
Page 24
25
Page 25
26
Page 26
27
Page 27
28
Page 28
29
Page 29
30
Page 30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
Page 24/121

Download datasheet (2Mb)Embed
PrevNext
PCM9211
SBAS495 – JUNE 2010
STATE of
synchronous
SYNCHRONIZATION
ADC
DOUT
Figure 17. ADC Output for Lost Synchronization
Setting the ADC Sampling Frequency with XTI as Clock Source
Register 31h holds the bytes that control the dividers used to bring the high-speed, 24.567-MHz clock down to
SCK, BCK, and LRCK as used by the ADC.
While the registers allow operation beyond 96 kHz, the ADC itself does not.
Analog Inputs to the ADC
The ADC module of the PCM9211 has two independent input channels: V
unbalanced inputs, each capable of 0.6 V
a buffering operational amplifier and a low-pass filter.
V
Output
COM
One unbuffered common voltage output pin, V
internally biased to a dc voltage level of 0.5 V
ADC. This pin may be used to bias external circuitry (such as an ADC driver op amp), but the load impedance
must be high enough because the output impedance of this pin is typically 12.5 kΩ.
Oversampling Rate
The oversampling rate of the PCM9211 ADC is fixed at 64f
External ADC Mode
To use an external ADC instead of the integrated ADC, the PCM9211 supports External ADC Mode. This option
enables a connection with an external, 192-kHz capable ADC via the MPIO_B ports. The external ADC must be
a clock slave to the PCM9211. The clock source for the external ADC can be selected using Register
42h/ADCLK (the same register that controls the clock source for the internal ADC).
To lower power consumption in the PCM9211, the onboard ADC can be set to power-down state using Register
40h/ADDIS.
To use the external ADC mode, Register 6Fh/MPBSEL must be set to '101' (External Slave ADC Input). Then,
each MPIO_B port is assigned for MPIO_B0 = EASCKO (output), MPIO_B1 = EABCKO (output), MPIO_B2 =
EALRCKO (output), and MPIO_B3 = EADIN (input). The MPIO_B pins should be connected according to this
configuration:
MPIO_B0 to ADC system clock input
MPIO_B1 to ADC bit clock input
MPIO_B2 to ADC LR clock input
MPIO_B3 to ADC data output
24
Submit Documentation Feedback
Asynchronous
synchronous
within 2 /f S
t ADCDLY
32/f S
Undefined data
Normal
ZERO
NOTE
V
input with 10-kΩ input resistance (typ). The ADC also integrates
CC
PP
(pin 44) is brought out for decoupling purposes. This pin is
COM
(nominal), and is used as internal reference voltage for the
CCAD
.
S
Product Folder Link(s):
PCM9211
www.ti.com
3
Normal
L and V
R. These are single-ended,
IN
IN
Copyright © 2010, Texas Instruments Incorporated