NCSE119A Nichia, NCSE119A Datasheet - Page 15

• Manufacturer Part Number: NCSE119A
• Manufacturer: Nichia

Specifications of NCSE119A

• Size Lxwxh (mm): 3.5x3.5x2.0
• Lumi-nous Inten-sity Typ(cd): 31
• Lumi-nous Flux Typ(lm)): 98.0
• Forward Voltage Vf(v) Typ: 3.50
• Forward Voltage Vf(v) Max: 4.00
• Directivity (degree): 120
• If (ma): 350
• Mounting Style: Through Hole

CAUTIONS
(1) Storage
(2) Directions for Use
(3) Handling Precautions
● Product complies with JEDEC MSL 3 or equivalent. See IPC/JEDEC STD-020 for moisture-sensitivity details.
● Absorbed moisture in LED packages can vaporize and expand during soldering, which can cause interface delamination
● After opening the moisture-proof aluminum bag, the products should go through the soldering process
● After the “Period After Opening” storage time has been exceeded or silica gel desiccants are no longer blue,
● Although the leads or electrode pads (anode and cathode) of the product are plated with gold,
● Do not use sulfur-containing materials in commercial products. Some materials, such as seals and adhesives, may contain sulfur.
● To prevent water condensation, please avoid large temperature and humidity fluctuations for the storage conditions.
● When designing a circuit, the current through each LED must not exceed the Absolute Maximum Rating.
● LEDs should be operated in forward bias. Driving circuits must not subject LEDs to either forward or reverse voltage while off.
● For stabilizing the LED characteristics, it is recommended to operate at greater than 10% nominal current.
● For outdoor use, necessary measures should be taken to prevent water, moisture and salt air damage.
● Do not handle LEDs with bare hands, it may contaminate the LED surface and affect optical characteristics.
● When handling the product with tweezers, be careful not to apply excessive force to the resin.
● Dropping the product may cause damage.
● Do not stack assembled PCBs together. Failure to comply can cause the resin portion of the product to be cut, chipped,
Storage
Baking
and result in optical performance degradation. Products are packed in moisture-proof aluminum bags
to minimize moisture absorption during transportation and storage.
Included silica gel desiccants change from blue to red if moisture had penetrated bags.
within the range of the conditions stated above. Unused remaining LEDs should be stored with silica gel desiccants
in a hermetically sealed container, preferably the original moisture-proof bags for storage.
the products should be baked. Baking should only be done once.
prolonged exposure to a corrosive environment might cause the gold plated the leads or electrode pads to tarnish,
and thus leading to difficulties in soldering. If unused LEDs remain, they must be stored in a hermetically sealed container.
Nichia recommends using the original moisture-proof bag for storage.
The contaminated plating of LEDs might cause an open circuit. Silicone rubber is recommended as a material for seals.
Bear in mind, the use of silicones may lead to silicone contamination of electrical contacts inside the products,
caused by low molecular weight volatile siloxane.
Operating at a constant current per LED is recommended. In case of operating at a constant voltage, Circuit B is recommended.
If the LEDs are operated with constant voltage using Circuit A, the current through the LEDs may vary due to the variation
in Forward Voltage characteristics of the LEDs.
Continuous reverse voltage can cause migration and LED damage.
In the worst case, catastrophic failure from excess pressure through bump-bond breaks and package damage may result.
Otherwise, The resin can be cut, chipped, delaminate or deformed, causing bump-bond breaks and catastrophic failures.
delaminated and/or deformed. It may cause bump to break, leading to catastrophic failures.
Before Opening Aluminum Bag
After Opening Aluminum Bag
(A)
Conditions
≤30°C
≤30°C
65±5°C
Temperature
(B)
≤90%RH
≤70%RH
-
Humidity
Within 1 Year from Delivery Date
≤168hours
≥24hours
Time
14