AD8591ART Analog Devices, AD8591ART Datasheet
AD8591ART
Available stocks
Related parts for AD8591ART
AD8591ART Summary of contents
Page 1
... AD8594, quad, is available in 16-lead narrow SOIC and 16-lead TSSOP packages. REV. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices ...
Page 2
AD8591/AD8592/AD8594–SPECIFICATIONS ELECTRICAL CHARACTERISTICS Parameter INPUT CHARACTERISTICS Offset Voltage Input Bias Current Input Offset Current Input Voltage Range Common-Mode Rejection Ratio Large Signal Voltage Gain Offset Voltage Drift Bias Current Drift Offset Current Drift OUTPUT CHARACTERISTICS Output Voltage High Output Voltage ...
Page 3
ELECTRICAL CHARACTERISTICS Parameter INPUT CHARACTERISTICS Offset Voltage Input Bias Current Input Offset Current Input Voltage Range Common-Mode Rejection Ratio Large Signal Voltage Gain Offset Voltage Drift Bias Current Drift Offset Current Drift OUTPUT CHARACTERISTICS Output Voltage High Output Voltage Low ...
Page 4
... Package Type 6-Lead SOT-23 (RT) S 10-Lead SOIC (RM) 16-Lead SOIC (R) 16-Lead TSSOP (RU) NOTE 1 is specified for worst case conditions, i.e., JA for surface mount packages. Model AD8591ART – +85 C AD8592ARM – +85 C AD8594AR AD8594ARU – +85 C 10k ...
Page 5
0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 0.75 1.25 1.75 2.25 2.75 3 SUPPLY VOLTAGE – Volts Figure 4. Supply Current per Amplifier vs. Supply Voltage +2.7V, + ...
Page 6
AD8591/AD8592/AD8594 200 V = +5V S 180 160 140 120 100 10k 100k 1M 10M 100M FREQUENCY – Hz Figure 13. ...
Page 7
100 + 500mV 500ns Figure 22. Large Signal Transient Response V = +5V S 100 A = 1000 ...
Page 8
AD8591/AD8592/AD8594 AD8591/AD8592/AD8594 APPLICATION SECTION Theory of Operation The AD859x family of amplifiers are all CMOS, high output drive, rail-to-rail input and output single supply amplifiers designed for low cost and high output current drive. The parts include a power saving ...
Page 9
In any application, the absolute maximum junction temperature must be limited to +150 C. If this junction temperature is ex- ceeded, the device could suffer premature failure. If the output voltage and output current are in phase, for example, with ...
Page 10
AD8591/AD8592/AD8594 If gain is required from the output amplifier, four additional resistors should be added as shown in Figure 35. The gain of the AD8592 can be set as +5V R7 20k V DD ...
Page 11
The U1-A amplifier is configured as a unity gain buffer driving capacitor. The input signal is connected to the noninverting input, while the sample clock controls the shutdown for that amplifier. When the sample clock is high, ...
Page 12
... This model, shown in Listing 1, is based on typical values for the device and can be downloaded from Analog Devices’ Internet site at www.analog.com. The model uses a common source output stage to provide rail- to-rail performance. This allows realistic simulation of open- loop gain dependency on load resistance as well as maximum output voltage versus output current ...
Page 13
... Listing 1: AD859x SPICE Macro-Model * AD8592 SPICE Macro-Model Typical Values * 9/98, Ver TAM / ADSC * * Copyright 1998 by Analog Devices * * Refer to “README.DOC” file for License * Statement. Use of this * model indicates your acceptance of the * terms and provisions in * the License Statement Node Assignments * noninverting input * | inverting input ...
Page 14
AD8591/AD8592/AD8594 CPS2 50 71 1E-5 EPSY 98 72 POLY(2) (70,0) (0,71 RPS3 72 73 1.59E6 CPS3 72 73 500E-12 RPS4 INTERNAL VOLTAGE REFERENCE * EREF 98 0 POLY(2) (99,0) (50, ...
Page 15
SOT (RT-6) 0.122 (3.10) 0.106 (2.70 0.071 (1.80) 0.118 (3.00) 0.059 (1.50) 0.098 (2.50 PIN 1 0.037 (0.95) BSC 0.075 (1.90) BSC 0.051 (1.30) 0.057 (1.45) 0.035 (0.90) 0.035 (0.90) 0.020 (0.50) 0.059 ...