B57213P0309M3 Epcos, B57213P0309M3 Datasheet

Page 1

... NTC thermistors for inrush current limiting Leaded and coated disks, P13 series Series/Type: B57213P0*09M3*1 Date: September 2011 © EPCOS AG 2011. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. ...

Page 2

... C) P 3.8 max (in air) approx (in air) approx approx. 1200 min test (@ 110 V AC max F 1880 0.074 1880 0.097 1880 0.106 Page B57213P0*09M3*1 P13 mW/K s mJ/K Ordering code B57213P0309M3*1 B57213P0409M3*1 B57213P0509M3*1 ...

Page 3

Inrush current limiters ICLs Reliability data Test Standard Storage in IEC dry heat 60068-2-2 Storage in damp IEC heat, steady state 60068-2-78 Rapid temperature IEC cycling 60068-2-14 Endurance IEC 60539-1 Cyclic IEC endurance 60539-1 Maximum IEC permissible 60539-1 capacitance test ...

Page 4

Inrush current limiters ICLs Taping and packing 1 Taping of radial leaded ICL NTC thermistors according to the specified lead spacing Dimensions and tolerances Lead spacing F = 5.0 mm (taping to IEC 60286-2) Lead spacing F = 7.5 mm ...

Page 5

Inrush current limiters ICLs Dimensions (mm) Lead Tolerance of spacing lead spacing 12.0 max. th 6.0 max. d 0.5/0.6 0.05 P 12.7 0 3.85 0 5.0 +0.6/ 0 2.0 ...

Page 6

Inrush current limiters ICLs Types of packing Reel packing Reel dimensions (in mm) Reel type d I 360 max. II 500 max. Bulk packing The components are packed in cardboard boxes, the size of which depends on the order quantity. ...

Page 7

Inrush current limiters ICLs Mounting instructions 1 Soldering 1.1 Leaded NTC thermistors Leaded thermistors comply with the solderability requirements specified by CECC. When soldering, care must be taken that the NTC thermistors are not damaged by excessive heat. The following ...

Page 8

Inrush current limiters ICLs Wave soldering Temperature characteristic at component terminal with dual wave soldering 2 Robustness of terminations The leads meet the requirements of IEC 60068-2-21. They may not be bent closer than 4 mm from the solder joint ...

Page 9

... The components should be left in the original packing. Touching the metallization of unsoldered thermistors may change their soldering properties. Storage temperature: Max. relative humidity (without condensation): Solder the thermistors listed in this data book after shipment from EPCOS within the time speci- fied: Leaded components: Please read Cautions and warnings and Important notes at the end of this document ...

Page 10

... Avoid contamination of thermistors surface during storage, handling and processing. Avoid storage of thermistor in harmful environments like corrosive gases (SO Solder thermistors after shipment from EPCOS within the time specified: Leaded components: 24 months Handling NTC thermistors must not be dropped. Chip-offs must not be caused during handling of NTCs. ...

Page 11

Inrush current limiters ICLs Mounting When NTC thermistors are encapsulated with sealing material or overmolded with plastic material, the precautions given in chapter “Mounting instructions”, “Sealing and potting” must be observed. Electrode must not be scratched before/during/after the mounting process. ...

Page 12

Inrush current limiters ICLs Symbols and terms Symbol English C Test capacitance test C Heat capacitance th I Current I Maximum current within stated max temperature range I NTC current NTC I Rated current R P Maximum power at 25 ...

Page 13

Inrush current limiters ICLs Abbreviations / Notes Symbol English * To be replaced by a number in ordering codes, type designations etc replaced by a letter. All dimensions are given in mm. The commas used in numerical ...

Page 14

... As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons always ultimately incum- bent on the customer to check and decide whether an EPCOS product with the properties de- scribed in the product specification is suitable for use in a particular customer application. ...