PIC16F88

Manufacturer Part NumberPIC16F88
ManufacturerMicrochip Technology Inc.
PIC16F88 datasheet
 
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Page 31
32
Page 32
33
Page 33
34
Page 34
35
Page 35
36
Page 36
37
Page 37
38
Page 38
39
Page 39
40
Page 40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
Page 38/228:

External Clock Input

Download datasheet (5Mb)Embed
PrevNext
PIC16F87/88
FIGURE 4-2:
CERAMIC RESONATOR
OPERATION (HS OR XT
OSC CONFIGURATION)
OSC1
(1)
C1
RES
F (3)
R
OSC2
S (2)
R
(1)
C2
Note 1: See Table 4-2 for typical values of C1 and
C2.
2: A series resistor (R
) may be required.
S
3: R
varies with the resonator chosen
F
(typically between 2 M to 10 M
TABLE 4-2:
CERAMIC RESONATORS
(FOR DESIGN GUIDANCE
ONLY)
Typical Capacitor Values Used:
Mode
Freq
OSC1
XT
455 kHz
56 pF
2.0 MHz
47 pF
4.0 MHz
33 pF
HS
8.0 MHz
27 pF
16.0 MHz
22 pF
Capacitor values are for design guidance only.
These capacitors were tested with the resonators
listed below for basic start-up and operation. These
values were not optimized.
Different capacitor values may be required to produce
acceptable oscillator operation. The user should test
the performance of the oscillator over the expected
V
and temperature range for the application.
DD
See the notes following this table for additional
information.
Note:
When using resonators with frequencies
above 3.5 MHz, the use of HS mode,
rather than XT mode, is recommended.
HS mode may be used at any V
which the controller is rated. If HS is
selected, it is possible that the gain of the
oscillator will overdrive the resonator.
Therefore, a series resistor should be
placed between the OSC2 pin and the
resonator. As a good starting point, the
recommended value of R
S
DS30487C-page 36
4.3

External Clock Input

The ECIO Oscillator mode requires an external clock
source to be connected to the OSC1 pin. There is no
oscillator start-up time required after a Power-on
PIC16F87/88
Reset, or after an exit from Sleep mode.
In the ECIO Oscillator mode, the OSC2 pin becomes
an additional general purpose I/O pin. The I/O pin
Sleep
becomes bit 6 of PORTA (RA6). Figure 4-3 shows the
pin connections for the ECIO Oscillator mode.
To Internal
FIGURE 4-3:
Logic
Clock from
Ext. System
.
OSC2
56 pF
47 pF
33 pF
27 pF
22 pF
for
DD
is 330

EXTERNAL CLOCK INPUT

OPERATION
(ECIO CONFIGURATION)
OSC1/CLKI
PIC16F87/88
RA6
I/O (OSC2)
 2005 Microchip Technology Inc.