PS240128WRF Powertip Technology, PS240128WRF Datasheet
PS240128WRF
Related parts for PS240128WRF
PS240128WRF Summary of contents
Page 1
...
Page 2
RECORDS OF REVISION Date Rev. 2006/04/19 0 PE240128WRF-001-HQ VER.0 Description MASS PRODUCTION Page2 Page Design by --- PETER Total：27 Page ...
Page 3
Contents 1. SPECIFICATIONS 1.1 Features 1.2 Mechanical Specifications 1.3 Absolute Maximum Ratings 1.4 DC Electrical Characteristics 1.5 Optical Characteristics 1.6 Backlight Characteristics 2. MODULE STRUCTURE 2.1 Counter Drawing 2.2 Interface Pin Description 2.3 Timing Characteristics 2.4 Display Command 3. QUALITY ...
Page 4
SPECIFICATIONS 1.1 Features Item Display Type LCD Type Driver Condition Viewing Direction Backlight Type Weight Interface Driver IC 1.2 Mechanical Specifications Item Outline Dimension Viewing Area Active Area Dot Size Dot Pitch Note : For detailed information please refer ...
Page 5
DC Electrical Characteristics Item Logic Supply Voltage High-level Input Voltage Low-level Input Voltage High-level Output Voltage Low-level Input Voltage Supply Current LCM Driver Voltage NOTE:*1 The VOP test point is Vo – Vss. NOTE:2 :Recommended Power Supply Combinations 1.5 ...
Page 6
Note 1. Optical characteristics-2 Viewing angle Left (9H) φ =180° PE240128WRF-001-HQ VER.0 Top (θ=0°) θL θ+ θ- Front (6H) φ =270° Viewing angle Page6 Rear (12H) φ =90° θR Right (3H) φ =0° ...
Page 7
Note 2. Optical characteristics-3 Fig.2 Definition of response time No selected waveform Transmittance No selected waveform Transmittance PE240128WRF-001-HQ VER.0 Positive Type Selected waveform 90% 100% Tr Negative Type Selected waveform 100% 90% Tr Page7 No selected waveform 10 ...
Page 8
Electrical characteristics-2 ※2 Drive waveform Vop: Drive voltage 1/B: Bias N: Duty (1) Selected waveform V Vop/B Vop/B V (2) Non- Selected waveform (1-2/B)Vop Vop/B Vop/B (1-2/B)Vop Note: Frame frequency is defined as follows: Common side supply voltage peak - ...
Page 9
Note 3. : Definition of Vth 100 73% Transmittanc 50% View direction Drive waveform Transmittance ※1 Contrast ratio = (Brightness in OFF state) / (Brightness in ON state) Outline of Electro-Optical Characteristics Measuring System Temperatur e Control Chamber PE240128WRF-001-HQ VER.0 ...
Page 10
Backlight Characteristics LCD Module with LED Backlight Maximum Ratings Item Forward Current Reverse Voltage Power Dissipation Electrical / Optical Characteristics Item Forward Voltage Reverse Current CIE Color Coordinate (With LCD) Average Brightness (with LCD) *1 Uniformity (With LCD)*2 Color ...
Page 11
MODULE STRUCTURE 2.1 Counter Drawing 2.1.1 LCM Mechanical Diagram * See Appendix 2.1.2 Block Diagram A K PIN34 PE240128WRF-001-HQ VER.0 LED BACKLIGHT COM0 240 * 128 DOTS COM63 LCD PANEL SEG0 ………………………… SEG239 ………………………… COM63 IC-ST7529 COM0 ………………………… Please ...
Page 12
Interface Pin Description Pin No. Symbol Register select input pin A0 = "H": DB0 to DB8 or SI are display data 1 A0 − "L": DB0 to DB8 or SI are control data − Read / Write ...
Page 13
Pin No. Symbol 13 IF1 14 IF3 Chip select input pins 15 XCS Data/instruction I/O is enabled only when XCS is "L". When chip select is non-active, DB0 to DB8 may be high impedance. 16 VSS Power supply (VSS=0) 17 ...
Page 14
Pin No. Symbol LCD driver supply voltages 30 V4 V0In & V0out should be connected together in FPC area. Voltages should have the following relationship ≧ V1 ≧ V2 ≧ V3 ≧ V4 ≧ VSS When the ...
Page 15
Timing Characteristics For the 8080 Series MPU Item Address hold time Address setup time System cycle time Enable L pulse width (Write) Enable H pulse width (Write) Enable L pulse width (Read) Enable H pulse width (Read) WRITE Data ...
Page 16
For the 6800 Series MPU Item Address hold time Address setup time System cycle time Enable L pulse width (Write) Enable H pulse width (Write) Enable L pulse width (Read) Enable H pulse width (Read) WRITE Data setup time WRITE ...
Page 17
Reset Timing Item Reset time Reset “L” pulse width PE240128WRF-001-HQ VER.0 Signal Symbol Condition - t R RES t RW Page17 25ºC DD Rating Min Typ Max - - ...
Page 18
Display Command PE240128WRF-001-HQ VER.0 Page18 ...
Page 19
PE240128WRF-001-HQ VER.0 Page19 ...
Page 20
QUALITY ASSURANCE SYSTEM 3.1 Quality Assurance Flow Chart Item Customer Sales Info Request Inquiry Marketing & Design NG Contract Sample Approval NG Pilot Run & Mass Product Ship Shipment Out PE240128WRF-001-HQ VER.0 R&D Q.A Survey Project evaluation Project Validation ...
Page 21
Item Customer Sales Info Claim Analysis report Sales Service 1. ISO 9001 Maintenance Activities Q.A 3. Equipment calibration Activity 5. Standardization Management PE240128WRF-001-HQ VER.0 Manufact R&D Q.A uring Failure analysis Corrective action Tracking 2. Process improvement proposal 4. Education And ...
Page 22
Inspection Specification Inspection Standard : MIL-STD-105E Table Normal Inspection Single Sampling Level II Equipment : Gauge , MIL-STD , Powertip Tester , Sample IQC Defect Level : Major Defect AQL 0.4; Minor Defect AQL 1.5 FQC Defect Level : ...
Page 23
NO Item Appearance of molding 6 A ╱2 Appearance of frame 7 A ╱2 Electrical characteristic of backlight 8 A ╱2 Assembly parts 10 A ...
Page 24
RELIABILITY TEST 4.1 Reliability Test Condition NO Item High Temperature 1 Storage Low Temperature 2 Storage High Temperature 3 /Humidity Storage 4 Temperature Cycling 5 Vibration 6 ESD Test 7 Drop Test PE240128WRF-001-HQ VER.0 Test Condition Storage at 80 ...
Page 25
PRECAUTION RELATING PRODUCT HANDLING 5.1 SAFETY 5.1.1 If the LCD panel breaks , be careful not to get the liquid crystal to touch your skin. 5.1.2 If the liquid crystal touches your skin or clothes , please wash it ...
Page 26
...
Page 27
...