PM4328-PI PMC-Sierra, Inc., PM4328-PI Datasheet - Page 154
PM4328-PI
Manufacturer Part Number
PM4328-PI
Description
Framer, T1|E1|T3 Standard Format, 324-BGA
Manufacturer
PMC-Sierra, Inc.
Datasheet
1.PM4328-PI.pdf
(250 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PM4328-PI
Manufacturer:
ATMEL
Quantity:
320
- Current page: 154 of 250
- Download datasheet (2Mb)
STANDARD PRODUCT
DATASHEET
PMC-2011596
PROPRIETARY AND CONFIDENTIAL
Clear, and TDPR Transmit Data register should be accessed (with respect to
WRB rising edge and RDB falling edge) at a rate no faster than 1/8 that of the
selected TDPR high-speed system clock. This time is used by the high-speed
system clock to sample the event, write the FIFO, and update the FIFO status.
Instantaneous variations in the high-speed reference clock frequencies (e.g. jitter
in the line clock) must be considered when determining the procedure used to
read and write the TDPR registers.
Upon reset of the TECT3, the TDPR should be disabled by setting the EN bit in
the TDPR Configuration Register to logic 0 (default value). An HDLC all-ones
Idle signal will be sent while in this state. The TDPR is enabled by setting the EN
bit to logic 1. The FIFOCLR bit should be set and then cleared to initialize the
TDPR FIFO. The TDPR is now ready to transmit.
To initialize the TDPR, the TDPR Configuration Register must be properly set. If
FCS generation is desired, the CRC bit should be set to logic 1. If the block is to
be used in interrupt driven mode, then interrupts should be enabled by setting
the FULLE, OVRE, UDRE, and LFILLE bits in the TDPR Interrupt Enable register
to logic 1. The TDPR operating parameters in the TDPR Upper Transmit
Threshold and TDPR Lower Interrupt Threshold registers should be set to the
desired values. The TDPR Upper Transmit Threshold sets the value at which the
TDPR automatically begins the transmission of HDLC packets, even if no
complete packets are in the FIFO. Transmission will continue until the current
packet is transmitted and the number of bytes in the TDPR FIFO falls to, or
below, this threshold level. The TDPR will always transmit all complete HDLC
packets (packets with EOM attached) in its FIFO. Finally, the TDPR can be
enabled by setting the EN bit to logic 1. If no message is sent after the EN bit is
set to logic 1, continuous flags will be sent.
The TDPR can be used in a polled or interrupt driven mode for the transfer of
data. In the polled mode the processor controlling the TDPR must periodically
read the TDPR Interrupt Status register to determine when to write to the TDPR
Transmit Data register. In the interrupt driven mode, the processor controlling
the TDPR uses the INTB output, the one of the TECT3 Master Interrupt Source
registers, and the TECT3 TDPR Interrupt Status registers to identify TDPR
interrupts which determine when writes can or must be done to the TDPR
Transmit Data register.
Interrupt Driven Mode:
The TDPR automatically transmits a packet once it is completely written into the
TDPR FIFO. The TDPR also begins transmission of bytes once the FIFO level
exceeds the programmable Upper Transmit Threshold. The CRC bit can be set
to logic 1 so that the FCS is generated and inserted at the end of a packet. The
ISSUE 1
141
HIGH DENSITY T1/E1 FRAMER
AND M13 MULTIPLEXER
PM4328 TECT3
Related parts for PM4328-PI
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
High density T1/E1 framer with intefrated M13 multiplexer
Manufacturer:
PMC-Sierra, Inc.
Part Number:
Description:
2 Megabit (256K x 8) 5.0 Volt-only CMOS Flash Memory
Manufacturer:
PMC-Sierra, Inc.
Part Number:
Description:
Interface, Multi-rate Telecom Backplane SERDES for 2.5Gbit/s Interconnect
Manufacturer:
PMC-Sierra, Inc.
Part Number:
Description:
processor, Spectra-9953 Device Driver
Manufacturer:
PMC-Sierra, Inc.
Part Number:
Description:
Ethernet, 8 Channel 10/100 Ethernet over SONET/SDH Mapping Device
Manufacturer:
PMC-Sierra, Inc.
Part Number:
Description:
Interface, Single Chip ADM for 622 & 155Mbit/s
Manufacturer:
PMC-Sierra, Inc.
Part Number:
Description:
Interface, Single Chip ADM for 622 & 155Mbit/s
Manufacturer:
PMC-Sierra, Inc.
Part Number:
Description:
Interface, Multi-rate SATURN User Network Interface for 2x622 and 4x155
Manufacturer:
PMC-Sierra, Inc.
Part Number:
Description:
SONET/SDH TRIBUTARY UNIT PAYLOAD PROCESSOR
Manufacturer:
PMC-Sierra, Inc.
Datasheet:
Part Number:
Description:
Processor, SONET/SDH Tributary Unit Payload Processor for 2488.32Mbit/s
Manufacturer:
PMC-Sierra, Inc.
Part Number:
Description:
HIGH DENSITY 84/63 CHANNEL VT/TU MAPPER AND M13 MULTIPLEXER
Manufacturer:
PMC-Sierra, Inc.
Datasheet:
Part Number:
Description:
SONET/SDH, Single Chip 96 Port SONET/SDH Cross-Connect Switch Element
Manufacturer:
PMC-Sierra, Inc.
Part Number:
Description:
ATM, Sixteen Channel ATM PHY Interface for 155.52 Mbps
Manufacturer:
PMC-Sierra, Inc.
Part Number:
Description:
ATM UNI, Single Channel ATM PHY Interface for 2488.32Mbps
Manufacturer:
PMC-Sierra, Inc.
Datasheet:
Part Number:
Description:
Interface, 4-Channel ATM and Bit HDLC User Network Interface
Manufacturer:
PMC-Sierra, Inc.