SG6980D Fairchild Semiconductor, SG6980D Datasheet
SG6980D
Available stocks
Related parts for SG6980D
SG6980D Summary of contents
Page 1
... PFC loop, in which the overshoot and undershoot of the PFC voltage are clamped. If the feedback loop is broken, SG6980D shuts off to prevent extra-high voltage on output. The PFC gate driver can be synchronized with external SYNC signal and the switching noise can be reduced. ...
Page 2
... MARKING DIAGRAMS DIP S=SOP P: SG6980DTP XXXXXXXYWWV Y: Year; WW: Week V: Assembly Location ORDERING INFORMATION Part Number Pb-Free Package SG6980DDZ SG6980DSZ (Preliminary) © System General Corp. Version 1.0.1 (IAO33.0071. Lead Free XXXXXXXX: Wafer Lot 16-Pin DIP 16-Pin SOP - 2 - Product Specification SG6980D PIN CONFIGURATION IAC ...
Page 3
... NTC thermistor must be connected from this pin to ground. The impedance of the NTC thermistor decreases whenever the temperature increases. Once the voltage of the OTP pin drops below 1.2V, the SG6980D will be off, and will auto restart when the voltage is back to 1.4V. The resistance of a resistor connected between RI and ground determines the switching frequency. A resistor with a resistance between 15kΩ ...
Page 4
... Single-Stage PFC Controller BLOCK DIAGRAM © System General Corp. Version 1.0.1 (IAO33.0071. www.sg.com.tw • www.fairchildsemi.com Product Specification SG6980D September 17, 2007 ...
Page 5
... System General Corp. Version 1.0.1 (IAO33.0071.B0 Value 25 2 -0.3 to 25V -0 DIP SOP +150 -20~+125 -55 to +150 DIP SOP 260 4 250 Value - www.sg.com.tw • www.fairchildsemi.com Product Specification SG6980D Unit 0.8 W 0.4 ℃ ℃ 36.70 ℃/W 37.76 ℃ Unit ℃ September 17, 2007 ...
Page 6
... RI= 24KΩ,V = 15V; Gate Open DD V <V V =25V ON/OFF V -0.16V <V DD DD-ON 11.5 9 23.5 10 Test Conditions Min. RI= 24KΩ www.sg.com.tw • www.fairchildsemi.com Product Specification SG6980D Typ. Max. Unit µ µA 12.5 13 24.5 25 µs Typ. Max. Unit ...
Page 7
... REF 6.5 1.5 2 0.35 0. Test Conditions Min. Typ 1 1. 3.2 RI=24 KΩ (I =20+I • www.sg.com.tw • www.fairchildsemi.com Product Specification SG6980D Max. Unit 0. RMS-UVP-1 RMS-UVP-1 V +0.22 240 ms Max. Unit 3. KΩ 1.100 • REF REF 120 mV 120 µs 1.066 • REF REF µ ...
Page 8
... 15V 5nF OUT = 15V 5nF OUT = Test Conditions FB=2.5V I =1mA SINK Test Conditions RI = 24KΩ www.sg.com.tw • www.fairchildsemi.com Product Specification SG6980D Min. Typ. Max. Unit 90 100 110 µA 0.15 0.20 0.25 V 0.35 0.40 0.45 V 200 ns 250 330 430 ns Min. Typ. ...
Page 9
... RI=24KΩ (F -12.5) OSC RI = 24KΩ 100 200 RI = 24KΩ 15.8 RI=24KΩ 1 RI=31.2KΩ 1 Test Conditions Min. Typ www.sg.com.tw • www.fairchildsemi.com Product Specification SG6980D Max. Unit V 0.9 V KHz 250 KHz 500 ns µs 3 µs 3 µs Max. Unit 50 KΩ ...
Page 10
... Minimum synchronizing frequency ( - Product Specification SG6980D Reference Voltage ( Temperature REF - Temperature (℃ Temperature DD- ...
Page 11
... Recovery Level on OTP (V 1.4 3 1.4 1 1.3 9 1 Product Specification SG6980D ) vs VFB Temperature - Temperature (℃ Temperature MO Temperature (℃ ...
Page 12
... PFC loop, in which the overshoot and undershoot of the PFC voltage are clamped. If the feedback loop is broken, the SG6980D shuts off the PFC to prevent extra-high voltage on output. Programmable two-level high/low line compensation optimizes THD performance. ...
Page 13
... OUT and SYNC signals. FIG.3 Synchronized Interleaving-Switching RDY Signal Section SG6980D provides a RDY pin to inform the next stage and other applications. RDY signal is high impedance when the FB voltage goes up to 2.7V and the delay around 5ms. Use the pin to turn on the second stage PWM when the bulk capacitor voltage is high enough ...
Page 14
... If the feedback resistance is opened, SG6980D shuts off immediately to prevent extra-high voltage on the output capacitor. © System General Corp. Version 1.0.1 (IAO33.0071.B0 (6) -------------- (7) FIG. 5 Voltage Error Amplifier with Multi-Vector ...
Page 15
... SG6980D to the decoupling capacitor, which should be low impedance and as short as possible. The ground trace 2 provides a signal ground. It should be connected directly to the decoupling capacitor C to the ground pin of the SG6980D. The ground trace 3 is independently tied from the decoupling capacitor to the PFC output capacitor C capacitor C O switching ...
Page 16
... Product Specification SG6980D θ Typ. Max. 0.210 0.130 0.135 0.060 0.018 0.755 0.775 0.300 0.248 0.255 0.100 0.130 0.150 0.355 0.375 ° ...
Page 17
... Product Specification SG6980D Detail Detail A Typ. Max. 0.069 0.010 0.059 0.016 0.008 0.394 0.157 0.050 0.244 0.050 0.015X45 ° 0.004 8 ° ...
Page 18
... Single-Stage PFC Controller © System General Corp. Version 1.0.1 (IAO33.0071. www.sg.com.tw • www.fairchildsemi.com Product Specification SG6980D September 17, 2007 ...