KVR1333D3S4R9S-2G

Manufacturer Part NumberKVR1333D3S4R9S-2G
DescriptionDram Module Ddr3 Sdram 2gbyte 240rdimm
ManufacturerETC-unknow
KVR1333D3S4R9S-2G datasheet
 
1
Page 1
2
Page 2
Page 1/2

Download datasheet (181Kb)Embed
Next
KVR1333D3S4R9S/2G
2GB 256M x 72-Bit PC3-10600
CL9 Registered w/Parity 240-Pin DIMM
DESCRIPTION:
This document describes ValueRAM's 256M x 72-bit 2GB (2048MB) DDR3-1333 CL9 SDRAM (Synchronous DRAM)
registered w/parity, single-rank memory module, based on eighteen 256M x 4-bit DDR3-1333 FBGA components. The
SPD is programmed to JEDEC standard latency 1333Mhz timing of 9-9-9 at 1.5V. This 240-pin DIMM uses gold contact
fingers and requires +1.5V. The electrical and mechanical specifications are as follows:
FEATURES:
JEDEC standard 1.5V ± 0.075V Power Supply
VDDQ = 1.5V ± 0.075V
667MHz fCK for 1333Mb/sec/pin
8 independent internal bank
Programmable CAS Latency: 6,7,8,9
Posted CAS
Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
Programmable CAS Write Latency(CWL) = 7(DDR3-1333)
8-bit pre-fetch
Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with tCCD = 4
which does not allow seamless read or write [either on the fly using A12 or MRS]
Bi-directional Differential Data Strobe
On-DIMM thermal sensor (Grade B)
Internal(self) calibration : Internal self calibration through ZQ pin (RZQ : 240 ohm ± 1%)
On Die Termination using ODT pin
Average Refresh Period 7.8us at lower then TCASE 85°C, 3.9us at 85°C < TCASE . 95°C
Asynchronous Reset
PCB : Height 1.180” (30.00mm), double sided component
PERFORMANCE:
CL(IDD)
Row Cycle Time (tRCmin)
Refresh to Active/Refresh Command Time (tRFCmin)
Row Active Time (tRASmin)
Power
UL Rating
Operating Temperature
Storage Temperature
Document No. VALUERAM0770-001.A00
9 cycles
49.5ns (min.)
110ns
36ns (min.)
3.885 W (operating)
94 V - 0
o
o
0
C to 85
C
-55
o
C to +100
o
C
04/10/09
Page 1

KVR1333D3S4R9S-2G Summary of contents

  • Page 1

    ... KVR1333D3S4R9S/2G 2GB 256M x 72-Bit PC3-10600 CL9 Registered w/Parity 240-Pin DIMM DESCRIPTION: This document describes ValueRAM's 256M x 72-bit 2GB (2048MB) DDR3-1333 CL9 SDRAM (Synchronous DRAM) registered w/parity, single-rank memory module, based on eighteen 256M x 4-bit DDR3-1333 FBGA components. The SPD is programmed to JEDEC standard latency 1333Mhz timing of 9-9-9 at 1.5V. This 240-pin DIMM uses gold contact fingers and requires +1 ...

  • Page 2

    MODULE DIMENSIONS: (units = millimeters) Document No. VALUERAM0770-001.A00 ValueRAM Page 2 ...