M63028FP Renesas Electronics Corporation., M63028FP Datasheet
M63028FP
Available stocks
Related parts for M63028FP
M63028FP Summary of contents
Page 1
M63028/029FP Spindle Motor and 5ch Actuator Driver Features This chip driver IC for spindle motor and 5 channel actuators. All of the motor and actuator of optical disk drive system (CD- ROM etc.) can be drived by ...
Page 2
... M63028/029FP Block Diagram M63028FP: M63029FP: Reverse Detect HU+ HU- HV+ 120˚ HV- MATRIX HW+ HW- Hall Bias CTL Current comp. amp. Direction SPIN comp. REF SL1IN SL2IN FOIN TOIN X12 Rev.1.0, Sep.16.2003, page Logic CTL Current CTL amp. ...
Page 3
... HV– HV– sensor amp. input 19 HV+ HV+ sensor amp. input 20 HU– HU– sensor amp. input 21 HU+ HU+ sensor amp. input Function FO, TO Gain M63028FP 12V/V M63029FP 12V/V Rev.1.0, Sep.16.2003, page Terminal Symbol Terminal Function 42 OSC PWM carrier oscilation set 41 MU1 ...
Page 4
M63028/029FP Absolute Maximum Rating (Ta=25°C) Symbol Parameter 5VCC 5V Power Supply VM1 Motor power Supply 1 *note1 VM2 Motor power Supply 2 VM3 Motor power Supply 3 IoA Motor Output Current A IoB Motor Output Current B IoC Motor Output ...
Page 5
M63028/029FP Thermal Derating 6.0 (W) 5.0 4.0 3.0 2.0 1.0 0 This IC's package is POWER-SSOP, so improving the board on which the IC is mounted enables a large power dissipation without a heat sink. For example, using an 1 ...
Page 6
M63028/029FP Electrical Characteristics Common Symbol Parameter Icc1 Supply current Icc2 Sleep current Fosc PWM carrier frequency VinREF REF inout voltage range IinREF REF terminal input current VMU1LO MUTE1 terminal low voltage VMU1HI MUTE1 terminal high voltage IM1U MUTE1 terminal input ...
Page 7
M63028/029FP Electrical Characteristics Spindle Symbol Parameter Vdyc1 Dynamic range of output Control voltage dead Vdead1– zone 1 Vdead1+ Control voltage input Vin1 range 1 Gvo1 Control gain 1 Vlim1F Control limit 1F Vlim2F Control limit 2F Vlim1R Control limit 1R ...
Page 8
M63028/029FP Slide1, 2 Symbol Parameter Vdyc2 Dynamic range of output Vdead2– Control voltage dead zone 2 Vdead2+ Vin2 Control voltage input range 2 Gvo2 Control gain 2 Vlim2 Control limit 2 Tdon Output turn-on delay Tdoff Output turn-off delay Tdsw ...
Page 9
M63028/029FP Electrical Characteristics Loadhing Symbol Parameter Vdyc3-1 Dynamic range of output Vdyc3-2 Dynamic range of output Vin3 Control voltage input range 3 Gvo3 Control gain 3 Voff1 Output offset voltage Focus Symbol Parameter Conditions Vdyc4 Dynamic range of VM1 = ...
Page 10
M63028/029FP Channel Select Function Logic control Drive channel MU1 MU2 SPIN Loading SELECT Off SELECT Off SELECT Off SELECT Off SELECT ...
Page 11
M63028/029FP LO- VM3 2 - Coil + LO+ application (MCU: One port H/Z/L control) Logic contorol (Hi impedance Rev.1.0, Sep.16.2003, page Output Voltage [V] Vo Gvo = 8 [V/V] ...
Page 12
M63028/029FP Spindle channel The relationship between the differential voltage between SPIN and REF and the torque is shown in following Figure.The voltage gain[Gvo] is 1.0 [V/V] . The current gain[ Gio] is 2.0[ A/V] (at sensing resistor :0.5,and R1=, R2=0 ...
Page 13
M63028/029FP R2 CTL R1 1.65 v Slide channel The relationship between the differential voltage between SLIN and REF and the torque is shown in following Figure. The voltage gain[Gvo] is 1.0 [V/V]. The current gain is 2.0[A/V] (at sensing resistor ...
Page 14
M63028/029FP VM2 Rs RSL1 R2 CTL SL1IN R1 1.65v REF GND The example of current-gain and current-limit of SLIDE. Rs Ilim[A] 0.50 1.00 0.75 0.66 1.00 0.50 Gio* = R1/[(R1+R2)Rs] [A/V] Rev.1.0, Sep.16.2003, page 14 of ...
Page 15
M63028/029FP Focus/Tracking channel The focus and tracking channel is the voltage control drive using BTL . The focus and tracking is the same composition. The relationship between the differential voltage between FOIN and REF and the output voltage is shown ...
Page 16
M63028/029FP Direct PWM operation The spindle and the slide channel is controlled by the direct PWM control. Also, built-in the current limit circuit. This IC controls the motor current directly. FORWARD Current path timing 1. Current comp Current path 1 ...
Page 17
... Output current - M63028FP FG M63029FP Output FG function at Spindle Drive The FG terminal outputs the square pulse signal synchronizing with the Hall inputs timing. And,the FG terminal is open- collector output. Phase delay circuit at Slide Phase delay circuit is built in the IC to detect an output spike current, when the motor current direction is switching. ...
Page 18
M63028/029FP I/O circuit • • FOIN, TOIN, SPIN Hu+, Hu-, Hv+, SL1IN, SL2IN, LOIN+ Hv-, Hw+, Hw-, REF 5VCC 2K • • 5VCC 5VCC • 5VCC, VM3, FO+, FO-, TO+, TO-, LO+, LO- 5VCC VM3 LO+ LO- ...
Page 19
M63028/029FP The boards for thermal derating evaluation Board material Glass-epoxy FR-4 Size 70 × 70mm thickness t=1.6mm 1 and 2 layers material : copper :t= 18 µ m thickness POWER-SSOP 42P9R-K Heat sink Lead Chip Rev.1.0, Sep.16.2003, page 19 of ...
Page 20
M63028/029FP Application Circuit 5 ∼ 12V RS L2 Slide M RSL1 SLIDE RSP M This value is a recommended value and is not guaranteed performance. Parts No. Typ. RSP 0.33 RSL1, RSL2 2 Rh 200 R1, R2, R3, R4, R5, ...
Page 21
M63028/029FP Package Dimensions Rev.1.0, Sep.16.2003, page ...
Page 22
Sales Strategic Planning Div. Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble ...