V110A Vicor Corporation, V110A Datasheet
V110A
Related parts for V110A
V110A Summary of contents
Page 1
... Railway/Transportation system applications including communications systems, information display, lighting, control systems, ticket machines, passenger entertainment, public address systems, door control, industrial power systems and power generation systems. e.g. V110A24C400BL V110A Output Voltage Product Grade Temperatures (° 3.3 V Grade Operating Storage ...
Page 2
Electrical characteristics apply over the full operating range of input voltage, output load (resistive) and baseplate temperature, unless otherwise specified. All temperatures refer to the operating temperature at the center of the baseplate. Operating input voltage 66 Input surge withstand ...
Page 3
Primary Control Parallel) PC bias voltage 5.50 current limit 1.5 PC module disable 2.3 PC module enable delay PC module alarm PR emitter amplitude 5.7 PR emitter current 150 PR receiver impedance 375 PR receiver threshold ...
Page 4
Efficiency 79 Ripple and noise Output OVP setpoint 4.14 Dissipation, standby Load regulation Load current 0 Current limit 61.8 Short circuit current 42.4 Efficiency 80.5 Ripple and noise Output OVP setpoint 4.14 Dissipation, standby Load regulation Load current 0 Current ...
Page 5
Efficiency 85 Ripple and noise Output OVP setpoint 13.7 Dissipation, standby Load regulation Load current 0 Current limit 33.9 Short circuit current 23.3 Efficiency 86 Ripple and noise Output OVP setpoint 13.7 Dissipation, standby Load regulation Load current 0 Current ...
Page 6
Efficiency 85.6 Ripple and noise Output OVP setpoint 27.1 Dissipation, standby Load regulation Load current 0 Current limit 17 Short circuit current 11.6 Efficiency 87.5 Ripple and noise Output OVP setpoint 27.1 Dissipation, standby Load regulation Load current 0 Current ...
Page 7
Efficiency 88 Ripple and noise Output OVP setpoint 40.4 Dissipation, standby Load regulation Load current 0 Current limit 11.3 Short circuit current 3.2 Efficiency 87 Ripple and noise Output OVP setpoint 40.4 Dissipation, standby Load regulation Load current 0 Current ...
Page 8
The module may be disabled by pulling PC below 2.3 V with respect to the –Input. This may be done with an open collector transistor, relay, or optocoupler. Multiple converters may be disabled with a single transistor or relay either ...
Page 9
The output voltage of the converter can be adjusted or programmed via fixed resistors, potentiometers or voltage DACs. See Figures 7 and 8. +OUT +S Error SC Amp –S 0.033 μF 1 kΩ –OUT 1.23 V 1,000 Vout R (ohms) ...
Page 10
The PR pin supports paralleling for increased power with N+1 (N+M) redundancy and phased array capability. Modules of the same input voltage, output voltage, and power level will current share if all PR pins are suitably interfaced. Compatible interface architectures ...
Page 11
... G Long RoHS * Pin style designator follows the “B” after the output power and precedes the baseplate designator. Ex. V110A12T400BN2 — Long ModuMate Pins Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715 Set your site on VICOR at www.vicorpower.com • The +Out and –Out power buses should be designed to minimize and balance parasitic impedance from each module output to the load ...
Page 12
No. Function Label 0.300±0.015 1 +In + 7,62±0,38 0.23 Primary 5 Control 3 Parallel PR 0.300±0.015 7,62±0,38 4 –In – 5 –Out – 6 –Sense –S Secondary 7 SC Control 8 +Sense +S 9 +Out + Slotted or ...
Page 13
Vicor products are guaranteed for two years from date of shipment against defects in material or workmanship when in normal use and service. This warranty does not extend to products subjected to misuse, accident, or improper application or maintenance. Vicor ...