LCP-155A4HSRBX-0D Delta Electronics, Inc., LCP-155A4HSRBX-0D Datasheet
LCP-155A4HSRBX-0D
Related parts for LCP-155A4HSRBX-0D
LCP-155A4HSRBX-0D Summary of contents
Page 1
... The post-amplifier of the LCP-155A4HSRBx also includes a LOS (Loss Of Signal) circuit that provides a TTL logic-high output when an unusable optical signal level is detected. The LCP-155A4HSRBx transceiver is a Class 1 eye safety product. The optical power levels, under normal operation, are at eye safe level. DELTA ELECTRONICS, INC. ...
Page 2
... Notes: 2. Internally AC coupled and terminated to 100Ohm differential load. 3. Pull with a 4.7K – 10K Ohm resistor on host Board CC 4. Internally AC coupled, but requires a 100 Ohm differential termination at or internal to Serializer/ Deserializer. 5. These are 20%~80% values DELTA ELECTRONICS, INC. Symbol Min. Typ. Max. Ts -40 85 ...
Page 3
... Optical Characteristics (LCP-155A4HSRBx) (V =3.135V to 3.465V, Data Rate=125Mbps, PRBS=2 CC Parameter Transmitter Output Optical Power (Avg.) Optical Extinction Ratio Center Wavelength Spectral Width (RMS) Optical Rise/Fall Time Total Jitter(pk-pk) Transmitter eye mask definition {X1, X2, X3, Y1, Y2, Y3, Y4} Receiver Sensitivity (Avg.) Input Optical Wavelength LOS- De-Asserted (Avg.) LOS- asserted (Avg ...
Page 4
... VeeT Transmitter Ground 18 TD+ Transmit Data In 19 TD- Inv. Transmit Data In 20 VeeT Transmitter Ground Plug Seq.: Pin engagement sequence during hot plugging. DELTA ELECTRONICS, INC. Function Plug Seq Note 1 Note 2 3 Module disables on high or open 3 Note 3, 2 wire serial ID interface 3 ...
Page 5
... The inputs will accept differential swings of 500 – 2400 mV (250 – 1200 mV single-ended), though it is recommended that values between 500 and 1200 mV differential (250 – 600 mV single-ended) be used for best EMI performance. DELTA ELECTRONICS, INC. 5 www.deltaww.com 2007/11/6 ...
Page 6
... Recommend Circuit Schematic VCC Protocol Vcc Tx_Disable Tx_Fault Protocol IC SerDes IC Rx_LOS PLD / PAL DELTA ELECTRONICS, INC. 1uH 3.3V 1uH RES1 10uF 0.1uF 0.1uF Tx_Disable Tx_Fault VeeT RES1 10uF 0.1uF RD + 100 Ohms Rx_LOS 3.3V VeeR RES1 RES1 RES1 Mod_def 2 Mod_def 1 Mod_def 0 RES1 = 4.7k to 10k Ohms ...
Page 7
... Package Outline Drawing for Metal Housing with Bail de-latch Latch Color Identifier Black DELTA ELECTRONICS, INC. 7 www.deltaww.com 2007/11/6 Rev. 0D ...
Page 8
... Time TX_DISABLE to t_rest reset LOS Assert Time t_loss_on LOS Deassert Time t_loss_off Serial ID Clock Rate f_serial_clock DELTA ELECTRONICS, INC. Min. Max. Unit Time from rising edge of TX_DISABLE to µsec 10 when the optical output falls below 10% of nominal Time from falling edge of TX_DISABLE to ...
Page 9
... Example of initialization during hot plugging, TX_DISABLE negated. Detection of transmitter safety fault condition Unsuccessful recovery from safety fault condition DELTA ELECTRONICS, INC. Power on initialization of SFP, TX_DISABLE asserted Initialization during hot plugging of SFP TRANSCEIVER. SFP TX_DISABLE timing during normal operation. Successful recovery from transient safety fault condition ...
Page 10
... LCP-155A4HSRB EEPROM Serial ID Memory Contents (2-Wire Address A0h) Address Hex ASCII Address Hex ASCII Address Hex ASCII Address Hex ASCII Address Hex ASCII Address Hex ASCII ...
Page 11
... EN 60825-2: 2000 Component Recognition Underwriters Laboratories and Canadian Standards Association Joint Component Recognition for Information Technology Equipment Including Electrical Business Equipment Ordering information for SFP modules LCP-155A4HSRBx Temperature x: Blank +70 degree C H: -10 to +85 degree C T: -40 to +85 degree C DELTA ELECTRONICS, INC. Reference ...
Page 12
... Oct.16 2007 Modified the Byte6 of A0h from 00h to 20h Add the total jitter specification Oct. 23 2007 Add latch color identifier Modify the Byte5,Byte6,Byte11 and Byte12 of A0h. 0D Nov. 06, 2007 Modify the Byte 12 from 02h to 01h DELTA ELECTRONICS, INC. 12 www.deltaww.com 2007/11/6 Rev. 0D ...