IS61C5128AL Integrated Silicon Solution, Inc., IS61C5128AL Datasheet
IS61C5128AL
Available stocks
Related parts for IS61C5128AL
IS61C5128AL Summary of contents
Page 1
... Output Enable inputs, CE and OE. The active LOW Write Enable (WE) controls both writing and reading of the memory. A data byte allows Upper Byte (UB) and Lower Byte (LB) access. The IS61C5128AL/AS and IS64C5128AL/AS are packaged in the JEDEC standard 36-pin SOJ (400-mil), 32-pin sTSOP- I, 32-pin SOP, 44-pin TSOP-II and 32-pin TSOP-II packages A0-A18 ...
Page 2
... IS61C5128AL/AS IS64C5128AL/AS HIGH SPEED (IS61/64C5128AL) PIN CONFIGURATION 36-Pin SOJ (400-mil I/ I/ GND PIN DESCRIPTIONS A0-A18 Address Inputs ...
Page 3
... IS61C5128AL/AS IS64C5128AL/AS LOW POWER (IS61/64C5128AS) PIN CONFIGURATION 32-pin sTSOP (TYPE I) A11 A13 A18 6 A15 A17 9 A16 10 A14 11 A12 PIN DESCRIPTIONS A0-A18 Address Inputs CE Chip Enable 1 Input OE Output Enable Input WE Write Enable Input ...
Page 4
... IS61C5128AL/AS IS64C5128AL/AS TRUTH TABLE Mode Not Selected X H Output Disabled H L Read H L Write L L ABSOLUTE MAXIMUM RATINGS Symbol Parameter V Terminal Voltage with Respect to GND TERM T Storage Temperature STG P Power Dissipation Output Current (LOW) OUT Notes: 1 ...
Page 5
... IS61C5128AL/AS IS64C5128AL/AS OPERATING RANGE: HIGH SPEED OPTION (IS61/64C5128AL) Range Ambient Temperature Commercial 0°C to +70°C Industrial -40°C to +85°C Automotive -40°C to +125°C OPERATING RANGE: LOW POWER OPTION (IS61/64C5128AS) Range Ambient Temperature Commercial 0°C to +70°C Industrial -40°C to +85°C Automotive -40° ...
Page 6
... IS61C5128AL/AS IS64C5128AL/AS HIGH SPEED OPTION (IS61/64C5128AL) POWER SUPPLY CHARACTERISTICS Symbol Parameter Test Conditions I V Operating Supply Current I OUT I V Dynamic Operating Supply Current I OUT I TTL Standby Current (TTL Inputs ≥ CMOS Standby ≤ ...
Page 7
... IS61C5128AL/AS IS64C5128AL/AS READ CYCLE SWITCHING CHARACTERISTICS Symbol Parameter t Read Cycle Time RC t Address Access Time AA t Output Hold Time OHA CE Access Time t ACE OE Access Time t DOE OE to High-Z Output t (2) HZOE OE to Low-Z Output t (2) LZOE CE to High-Z Output t (2) HZCE ...
Page 8
... IS61C5128AL/AS IS64C5128AL/AS AC WAVEFORMS (1,2) READ CYCLE NO. 1 ADDRESS D OUT PREVIOUS DATA VALID (1,3) READ CYCLE NO. 2 ADDRESS LZCS HIGH-Z D OUT Notes HIGH for a Read Cycle. 2. The device is continuously selected. OE Address is valid prior to or coincident with CE LOW transitions ...
Page 9
... IS61C5128AL/AS IS64C5128AL/AS WRITE CYCLE SWITCHING CHARACTERISTICS Symbol Parameter t Write Cycle Time Write End t SCE t Address Setup Time AW to Write End t Address Hold from Write End HA t Address Setup Time SA WE Pulse Width (OE =High PWE WE Pulse Width (OE=Low PWE ...
Page 10
... IS61C5128AL/AS IS64C5128AL/AS AC WAVEFORMS WE Controlled WRITE CYCLE NO. 1 (WE ADDRESS DATA UNDEFINED OUT D IN Notes: 1. The internal write time is defined by the overlap of CE LOW and WE LOW. All signals must be in valid states to initiate a Write, but any one can go inactive to terminate the Write. The Data Input Setup and Hold timing are referenced to the rising or falling edge of the signal that terminates the Write ...
Page 11
... IS61C5128AL/AS IS64C5128AL/AS WRITE CYCLE NO. 2 (OE is HIGH During Write Cycle) ADDRESS OE CE LOW DATA UNDEFINED OUT D IN WRITE CYCLE NO. 3 (OE is LOW During Write Cycle) ADDRESS OE LOW CE LOW DATA UNDEFINED OUT D IN Notes: 1. The internal write time is defined by the overlap of CE LOW and WE LOW. All signals must be in valid states to initiate a Write, but any one can go inactive to terminate the Write ...
Page 12
... IS61C5128AL/AS IS64C5128AL/AS DATA RETENTION SWITCHING CHARACTERISTICS (HIGH SPEED) (IS61/64C5128AL) Symbol Parameter V V for Data Retention Data Retention Current DR t Data Retention Setup Time SDR t Recovery Time RDR Note: 1. Typical Values are measured 5V DATA RETENTION WAVEFORM (CE t SDR VDD 4 ...
Page 13
... IS61C5128AL/AS IS64C5128AL/AS DATA RETENTION SWITCHING CHARACTERISTICS (LOW POWER) (IS61/64C5128AS) Symbol Parameter V V for Data Retention Data Retention Current DR t Data Retention Setup Time SDR t Recovery Time RDR Note: 1. Typical Values are measured 5V DATA RETENTION WAVEFORM (CE t SDR VDD 4 ...
Page 14
... IS64C5128AL/AS HIGH SPEED (IS61/64C5128AL) ORDERING INFORMATION Industrial Range: –40°C to +85°C Speed (ns) Order Part No. 10 IS61C5128AL-10KI IS61C5128AL-10KLI IS61C5128AL-10TI IS61C5128AL-10TLI Automotive Range: –40°C to +125°C Speed (ns) Order Part No. 12 IS64C5128AL-12KA3 IS64C5128AL-12TA3 IS64C5128AL-12TLA3 LOW POWER (IS61/64C5128AS) ORDERING INFORMATION Industrial Range: –40°C to +85°C Speed (ns) Order Part No ...
Page 15
... Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — ...
Page 16
... BSC Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — ...
Page 17
... BSC Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products ...
Page 18
... D1 11.70 11.90 E 7.90 8.10 e 0.50 BSC L 0.30 0.70 S 0.28 Typ. α 0° 5° Integrated Silicon Solution, Inc. PK13197H32 Rev. B 04/21/ α Inches Min Max Notes: 1. Controlling dimension: millimeters, unless otherwise specified. 2. BSC = Basic lead spacing between centers. 3. Dimensions D1 and E do not include mold flash protru- — ...
Page 19
... Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — ...