AP2280 Diodes, Inc., AP2280 Datasheet
AP2280
Available stocks
Related parts for AP2280
AP2280 Summary of contents
Page 1
... DS(ON) capability with a low forward voltage drop. The turn-on slew rate of the device is controlled internally to reduce turn-on inrush current. The AP2280 load switch is designed to operate from 1.5V to 6.0V, making it ideal for 1.8V, 2.5V, 3.3V, and 5V systems. The typical quiescent supply current is only 0.004uA, making it ideal for battery powered consumption is a concern ...
Page 2
... OUT Block Diagram AP2280 Rev. 5 Single Channel Slew Rate Controlled Load Switch (2) DFN2018 Discharge pin. If DIS pin is tied to OUT pin externally, the output voltage will be discharged to ground when disabled. Ground. Voltage output pin. This is the pin to the P-channel MOSFET drain. ...
Page 3
... V IN Output Current (Note 4) I OUT T Operating Ambient Temperature A Notes: 4. Maximum output current depends on application conditions. Please refer to the application note section. AP2280 Rev. 5 Single Channel Slew Rate Controlled Load Switch OUT 0.1uF 1uF For applications with output discharge ...
Page 4
... Test condition for SOT25: Device mounted on FR-4 substrate PC board, with minimum recommended pad layout. 6. Test condition for DFN2018-6: Device mounted on FR-4 2-layer board, 2oz copper, with minimum recommended pad on top layer and 3 vias to bottom layer 1.0"x1.4" ground plane. AP2280 Rev. 5 Single Channel Slew Rate Controlled Load Switch Test Conditions ...
Page 5
... R vs. Input Voltage DS(ON) 300.00 250.00 200.00 150.00 100.00 50.00 1.5 2 2.5 3 3.5 Input Voltage (V) ENABLE Threshold vs. Input Voltage 1.8 1.6 1.4 1.2 1 0.8 0.6 0.4 1.5 2 2.5 3 3.5 Input Voltage (V) AP2280 Rev. 5 Single Channel Slew Rate Controlled Load Switch 0.020 0.015 0.010 0.005 0.000 4.0 5.0 6.0 200.00 I=100mA 180.00 I=500mA 160.00 I=1A 140.00 I=2A 120.00 100.00 80.00 60.00 40.00 20.00 0.00 4 4.5 5 5.5 6 ...
Page 6
... Time (50μs/div) AP2280-1 Turn-On (V =5V, R =10Ω (2V/div) V OUT (2V/div (500mA/div) Time (50μs/div) AP2280 Rev. 5 Single Channel Slew Rate Controlled Load Switch (Continued) =7Ω (2V/div) V OUT (2V/div (500mA/div (2V/div) V OUT (2V/div (500mA/div www ...
Page 7
... Time (500μs/div) AP2280-2 Turn-On (V =5V, R =10Ω (2V/div) V OUT (2V/div (500mA/div) Time (500μs/div) AP2280 Rev. 5 Single Channel Slew Rate Controlled Load Switch (Continued) =7Ω (2V/div) V OUT (2V/div (500mA/div (2V/div) V OUT (2V/div (200mA/div www ...
Page 8
... OUT and GND pins, and keep the traces as short as possible. Enable/Shutdown Operation The AP2280 is turned on by setting the EN pin high, and is turned off by pulling it low. To ensure proper operation, the signal source used to drive the EN pin must be able to swing above and below the ...
Page 9
... Green Package Information (1) Package type: SOT25 AP2280 Rev. 5 Single Slew Rate Controlled Load Switch (2) DFN2018-6 (Top View AP2280 AP2280 (All Dimensions in mm www.diodes.com AP2280 AP2280 AP2280 Year 0 Month A Green © Diodes Incorporated MAY 2008 ...
Page 10
... Package Information (2) Package type: DFN2018-6 0.10 C 6X- 0.08 C 2X- 0.25 B AP2280 Rev. 5 Single Slew Rate Controlled Load Switch (Continued) Side View 1.75/1.875 Pin #1 ID 1.3/1.5 0.50Typ Bottom View www.diodes.com AP2280 Seating Plane 0.30Typ 0.15/0.25 0. © Diodes Incorporated MAY 2008 ...
Page 11
... Diodes Incorporated and all the companies whose products are represented on our website, harmless against all damages. Diodes Incorporated products are not authorized for use as critical components in life support devices or systems without the expressed written approval of the President of Diodes Incorporated. AP2280 Rev. 5 Single Slew Rate Controlled Load Switch AB ...