MAX746 Maxim, MAX746 Datasheet - Page 14

• Manufacturer Part Number: MAX746
• Description: High-Efficiency / PWM / Step-Down / N-Channel DC-DC Controller
• Manufacturer: Maxim

High-Efficiency, PWM, Step-Down,
N-Channel DC-DC Controller
Table 1. Measured Output Voltage Sag
with 30mA to 3A Load Step*
*
For load currents up to 3A, 100µF (C2) in parallel with
0.1µF (C3) is adequate. Smaller bypass capacitors may
also be acceptable for lighter loads. The input voltage
source impedance determines the size of the capacitor
required at the V+ input. As with the output filter capaci-
tor, a low-ESR capacitor (Sanyo OS-CON, Sprague 595D
or equivalent) is recommended for input bypassing.
Figure 3a shows the charge-pump doubler circuit con-
figured with a 0.1µF charge-pump capacitor C8 and a
1.0µF reservoir capacitor C9. The ratio of the capaci-
tors, along with the input voltage, determines the
amount of ripple on HIGH. If the input supply range
exceeds 12V, increase C9 to 4.7µF to reduce the
charge-pump ripple. C9 should be 10µF for less.
Figure 3b shows the charge-pump tripler circuit.
Refer to Table 2 to determine the proper charge-pump
configuration (which is based on the minimum expect-
ed supply voltage at V+).
Some interaction occurs between the switch oscillator
and the charge-pump oscillator. This interaction modu-
lates the inductor-current waveform, but has negligible
impact on the output.
Soft-start provides a ramp to the full current limit. A typi-
cal value for the soft-start capacitor (C5) is 0.1µF,
which provides a 380ms soft-start time. Use values in
the 0.001µF to 1µF range. The nominal time for C5 to
reach its steady-state value is given by:
Note that t
MAX746 to power-up, although it does affect the start-
up time. The start-up time is also a function of the input
14
Circuit of Figure 1a.
CAPACITOR
OUTPUT
FILTER
C1 ( m F)
______________________________________________________________________________________
440
660
880
SS
t
does NOT equal the time it takes for the
SS
V
Soft-Start and Reference Capacitors
IN
400
260
200
(sec) = (C5) (3.8 x 10
=6V
FOR VARIOUS INPUT VOLTAGES
OUTPUT VOLTAGE SAG (mV)
V
IN
250
190
100
=6.5V
Charge-Pump Capacitors
V
IN
210
160
90
=7V
6
)
V
IN
140
70
40
=9V
V
IN
90
50
25
=10V
Table 2. Charge-Pump Configuration
*
voltage and load current. With a 3A load current, a 10V
input voltage, and a 0.1µF soft-start capacitor, it typi-
cally takes 240ms for the MAX746 to power up. A
0.47µF soft-start capacitor increases the start-up time
to approximately 2.3sec.
Bypass REF with a 1µF capacitor (C6).
With a fixed 5V output, connect a compensation capac-
itor (C7) between CC and AGND to optimize transient
response. Appropriate compensation is determined by
the size and ESR of the output filter capacitor (C1), and
by the load current.
In the standard 5V application circuit, 2.7nF is appro-
priate for load currents up to 3A; for lighter loads,
C7’s value can be reduced. If 2.7nF does not com-
pensate adequately, use the following equations to
determine C7.
For fixed 5V-output operation:
For adjustable-output operation, FB becomes the
compensation input pin, and CC and OUT are left
unconnected. Connect C7 between FB and GND in
parallel with R4 (Figure 6). C7 is determined by:
For example, with a fixed 5V output with C1 = 470µF
and an ESR
6V < V+ < 6.5V
temperature range, increase the 6.5V limit to 7V.
When using the voltage-doubler circuit over the military
V+ ≥ 6.5V
V+ ≤ 6V
V+
C1
*
C7 = _____________ = 1560pF
*
C7 = ___________________
of 0.04Ω (at a frequency of 100kHz):
C7 = _____________
(
Voltage tripler with 1N914 diodes for D2,
D3, D5, and D6
Voltage doubler with 1N5817 Schottky
diodes for D2 and D3
Voltage doubler with 1N914 diodes for
D2 and D3
C1
CHARGE-PUMP CONFIGURATION
(
) (
12kΩ
2
) (
(
ESR
C1
R4
C1
) (
12kΩ
C1
Compensation Capacitor
) (
ESR
)
ESR
R5
C1
C1
)
)