STK433-240A-E SANYO Semiconductor, STK433-240A-E Datasheet
STK433-240A-E
Related parts for STK433-240A-E
STK433-240A-E Summary of contents
Page 1
... Ordering number : EN*A1490 STK433-240A-E Overview The STK433-240A hybrid IC designed to be used in 40W × 3ch class AB audio power amplifiers. Applications • Audio power amplifiers. Features • Pin-to-pin compatible outputs ranging from 30W to 60W. • Can be used to replace the STK433-000/-100 series (30W to 150W/2ch) and STK433-300 series (80W to 150W/3ch) due to its pin compatibility. • ...
Page 2
... The impression voltage of ‘#13 (Stand-By) pin’ must not exceed the maximum rating. Power amplifier operate by impressing voltage +2.5 to +5.5V to ‘#13 (Stand-By) pin’. *8: A thermoplastic adhesive is used to adhere the case. Designated transformer power supply (MG-200 equivalent) STK433-240A-E Symbol V CC max (0) Non signal R L ≥6Ω ...
Page 3
... Package Dimensions unit:mm (typ) 67.0 60.0 3.6 1 2.0 (12.0) 18 2.0=36.0 Internal Equivalent Circuit 3 8 Pre Driver CH1 SUB 9 STK433-240A-E 9.0 (R1.8) 19 0.4 0.5 2.9 5.5 Bias Circuit Pre Pre Driver Driver CH3 CH2 MONO No. A1490-3/10 ...
Page 4
... CC 100μF /50V 100μF /50V GND 100μF /50V -V CC Sample PCB Trace Pattern www.DataSheet4U.com STK433-240A-E STK433-230A/240A-E Ch2 Ch2 Ch1 Ch2 Ch1 OUT OUT SUB GND NF +PRE IN NF ST- ...
Page 5
... R33 C32 J1, J2, J3, J4, J5, J6, J8, J9 J7, JS2, JS3, JS4, JS5, JS7, JS8, JS9 JS6, JS10 JS1 (*1) Capacitor mark “A” side is “-” (negative). (*2) Add parts C23 to the other side of PCB. www.DataSheet4U.com STK433-240A-E PARTS RATING - - ERG1SJ101 100Ω, 1W RN16S102FK 1kΩ, 1/6W RN16S563FK 56kΩ ...
Page 6
... STK433-030-E 30W/JEITA STK433-040-E 40W/JEITA STK433-060-E 50W/JEITA STK433-070-E 60W/JEITA STK433-090-E 80W/JEITA STK433-100-E 100W/JEITA STK433-120-E 120W/JEITA STK433-130-E 150W/JEITA 3-channel class-AB STK433-230A-E 30W/JEITA STK433-240A-E 40W/JEITA STK433-260A-E 50W/JEITA STK433-270-E 60W/JEITA STK433-290-E 80W/JEITA STK433-300-E 100W/JEITA STK433-320-E 120W/JEITA STK433-330-E 150W/JEITA 2-channel class-H STK415-090-E 80W/JEITA STK415-100-E 90W/JEITA STK415-120-E 120W/JEITA ...
Page 7
... Supply voltage ±V [Thermal Design Example for STK433-240A 6Ω)] The thermal resistance, θc-a, of the heat sink for total power dissipation, Pd, within the hybrid IC is determined as follows. www.DataSheet4U.com Condition 1: The hybrid IC substrate temperature, Tc, must not exceed 125°C. ...
Page 8
... OUT OUT 56kΩ 56kΩ 6.8kΩ www.DataSheet4U.com Load short protection circuit +V CC GND -V CC STK433-240A-E (when 1/8P O max. = 5.0W max. = 40W). θc-a < (125 − 50)/47.0 < 1.59 θc-a < (150 − 50)/47.0 − 4.2/6 < 1.42 STK433-200(A)-E series Ch2 Ch1 Ch1 Ch2 +PRE SUB GND ST-BY OUT IN NF ...
Page 9
... VST max. (*2) The pop noise level when the power is turned on can be reduced by setting the time constant with a capacitor in operating mode. (*3) Determines the time constant at which the capacitor (*2) is discharged in standby mode. STK433-240A-E Stand-By Circuit SW transistor in PreDriver IC Δ ...
Page 10
... SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellectual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of November, 2009. Specifications and information herein are subject to change without notice. STK433-240A-E No. A1490-10/10 PS ...