STK433-330-E Sanyo Semicon Device, STK433-330-E Datasheet
STK433-330-E
Related parts for STK433-330-E
STK433-330-E Summary of contents
Page 1
... STK433-290-E STK433-300-E 80W×3ch 100W×3ch 50W×3ch 60W×3ch ±54V ±57V ±47V ±50V ±33V ±36V 64.0mm×36.6mm×9.0mm www.DataSheet4U.com STK433-320-E STK433-330-E 120W×3ch 150W×3ch 80W×3ch 100W×3ch ±65V ±71.5V ±57V ±63V ±41V ±44V ' s products or 21710HKIM No. A1630-1/13 ...
Page 2
... The case of this Hybrid-IC is using thermosetting silicon adhesive (TSE322SX). *9: Weight of HIC: 24.8g Outer carton dimensions (W×L×H): 452mm×325mm×192mm Designated transformer power supply (MG-200 equivalent) STK433-290-E Symbol Conditions Non signal R L ≥6Ω Per one power transistor Should satisfy Tj max and Tc max V CC =± ...
Page 3
... Package Dimensions unit:mm (typ) 64.0 55 3.6 2.0 (9.8) 18 2.0=36.0 RoHS DIRECTIVE PASS Equivalent Circuit 3 8 Pre Driver CH1 SUB 9 STK433-290-E (R1.8) 9.0 2.9 0.4 0.5 5.5 Bias Circuit www.DataSheet4U.com Pre Pre Driver Driver CH2 CH3 MONO No. A1630-3/13 ...
Page 4
... CC -PRE +V CC OUT OUT OUT R21 R20 R08 C10 R23 R01 C23 C01 GND C02 PCB Layout Example STK433-290-E STK433-300sr Ch2 Ch1 Ch1 ST- Ch2 +PRE SUB GND OUT C19 R09 C11 ...
Page 5
... Capacitor for oscillation prevention. C19, C20, C21 68pF Capacitor for oscillation prevention. L01, L02, L03 3μH Coil for oscillation prevention. STK433-290-E Above Recommended Circuit purpose Output neutral voltage (VN) shift. (It is referred that R05=R08, R06=R09, R07=R10) It may oscillate. (VG<30dB) Decrease of maximum ...
Page 6
... J1, J2, J3, J4, J5, J6, J8, J9 J7, JS2, JS3, JS4, JS5, JS7, JS8, JS9 JS6, JS10 JS1 (*1) Capacitor mark “A” side is “-” (negative). (*2) STK433-100Sr (2ch AMP) doesn’t mount parts (*3) Add parts C23 to the other side of PCB. (*4) Recommended standby circuit is used. STK433-290-E PARTS ...
Page 7
... STK433-130-E 150W/JEITA 3ch class-AB (Size) 67.0×25.6×9.0 STK433-230A-E 30W/JEITA STK433-240A-E 40W/JEITA STK433-260A-E 50W/JEITA STK433-270-E 60W/JEITA (Size) 64.0×36.6×9.0 STK433-290-E 80W/JEITA STK433-300-E 100W/JEITA STK433-320-E 120W/JEITA STK433-330-E 150W/JEITA 1 2ch class-H (Size) 64.0×31.1×9.0 STK415-090-E 80W/JEITA + STK415-100-E 90W/JEITA V STK415-120-E 120W/JEITA L STK415-130-E 150W/JEITA STK415-140-E 180W/JEITA ...
Page 8
... Supply voltage ±V [Thermal Design Example for STK433-290 6Ω)] The thermal resistance, θc-a, of the heat sink for total power dissipation, Pd, within the hybrid IC is determined as follows. Condition 1: The hybrid IC substrate temperature, Tc, must not exceed 125°C. Pd × θc < 125°C ................................................................................................. (1) Condition 2: The junction temperature, Tj, of each power transistor must not exceed 150° ...
Page 9
... Therefore, the value of 0.82°C/W, which satisfies both of these formulae, is the required thermal resistance of the heat sink. Note that this thermal design example assumes the use of a constant-voltage power supply, and is therefore not a verified design for any particular user’s end product. STK433-300series Stand-by Control & Mute Control & Load-Short Protection Application Ch1 Ch1 ...
Page 10
... It can largely improve a pop noise to occur in power supply ON/OFF by using recommended Stand-By Control Application. • Because It can perform Stand-By Control by regulating limit resistance to the voltage such as used microcomputers, a set design is easy. (ex) STK433-300series test circuit. When impressed by Stand-by control control [+5V ...
Page 11
... Tr1 Tr2 (2) Load short Point.C detection part Ch1 OUT The protection circuit application for the STK433-300-Esr consists of the following blocks (blocks (1) to (4)). (1) Standby control circuit block (2) Load short-circuit detection block (3) Latch-up circuit block (4) DC voltage protection block STK433-290-E STK433-300-E series ...
Page 12
... Stand-by control circuit block (Reference example) STK433-300-E series test circuit (when +5V is applied to Stand-by control Ch1 Ch1 Ch2 Ch2 -PRE - +PRE SUB OUT OUT OUT OUT STK433-300-E series Concerning pin 13 reference voltage VST <1> Operation Mode The switching transistor in the bias circuit turns on and places the amplifier into the operating mode when the voltage flowing into pin 13 (VST) becomes 0 ...
Page 13
... SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellectual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of February, 2010. Specifications and information herein are subject to change without notice. STK433-290-E www.DataSheet4U.com PS No. A1630-13/13 ...