LPC2138 Philips Semiconductors, LPC2138 Datasheet - Page 7

• Manufacturer Part Number: LPC2138
• Description: (LPC2131 - LPC2138) Single-chip 16/32-bit microcontrollers 32/64/512 kB ISP/IAP Flash with 10-bit ADC and DAC
• Manufacturer: Philips Semiconductors

Philips Semiconductors
Table 3:
9397 750 14868
Preliminary data sheet
Symbol
P0.0 to P0.31
P0.0/TXD0/
PWM1
P0.1/RXD0/
PWM3/EINT0
P0.2/SCL0/
CAP0.0
P0.3/SDA0/
MAT0.0/EINT1
P0.4/SCK0/
CAP0.1/AD0.6
P0.5/MISO0/
MAT0.1/AD0.7
P0.6/MOSI0/
CAP0.2/AD1.0
P0.7/SSEL0/
PWM2/EINT2
P0.8/TXD1/
PWM4/AD1.1
P0.9/RXD1/
PWM6/EINT3
Pin description
Pin
19
21
22
26
27
29
30
31
33
34
5.2 Pin description
[1]
[2]
[3]
[3]
[4]
[4]
[4]
[2]
[4]
[2]
Type
O
O
I
O
I
I/O
I
I/O
O
I
I/O
I
I
I/O
O
I
I/O
I
I
I
O
I
O
O
I
I
O
I
I/O
Description
Port 0: Port 0 is a 32-bit I/O port with individual direction controls for each bit.
Total of 31 pins of the Port 0 can be used as a general purpose bi-directional
digital I/Os while P0.31 is output only pin. The operation of port 0 pins
depends upon the pin function selected via the pin connect block.
Pin P0.24 is not available.
TXD0 — Transmitter output for UART0.
PWM1 — Pulse Width Modulator output 1.
RXD0 — Receiver input for UART0.
PWM3 — Pulse Width Modulator output 3.
EINT0 — External interrupt 0 input
SCL0 — I
CAP0.0 — Capture input for Timer 0, channel 0.
SDA0 — I
MAT0.0 — Match output for Timer 0, channel 0.
EINT1 — External interrupt 1 input.
SCK0 — Serial clock for SPI0. SPI clock output from master or input to slave.
CAP0.1 — Capture input for Timer 0, channel 0.
AD0.6 — A/D converter 0, input 6. This analog input is always connected to
its pin.
MISO0 — Master In Slave OUT for SPI0. Data input to SPI master or data
output from SPI slave.
MAT0.1 — Match output for Timer 0, channel 1.
AD0.7 — A/D converter 0, input 7. This analog input is always connected to
its pin.
MOSI0 — Master Out Slave In for SPI0. Data output from SPI master or data
input to SPI slave.
CAP0.2 — Capture input for Timer 0, channel 2.
AD1.0 — A/D converter 1, input 0. This analog input is always connected to
its pin. Available in LPC2138 only.
SSEL0 — Slave Select for SPI0. Selects the SPI interface as a slave.
PWM2 — Pulse Width Modulator output 2.
EINT2 — External interrupt 2 input.
TXD1 — Transmitter output for UART1.
PWM4 — Pulse Width Modulator output 4.
AD1.1 — A/D converter 1, input 1. This analog input is always connected to
its pin. Available in LPC2138 only.
RXD1 — Receiver input for UART1.
PWM6 — Pulse Width Modulator output 6.
EINT3 — External interrupt 3 input.
Rev. 02 — 15 April 2005
LPC2131/2132/2134/2136/2138
2
2
C0 clock input/output. Open drain output (for I
C0 data input/output. Open drain output (for I
Single-chip 16/32-bit microcontrollers
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
2
2
C-bus compliance).
C-bus compliance).
7 of 41