MC100EP16VT ON Semiconductor, MC100EP16VT Datasheet

MC100EP16VT

Manufacturer Part Number

MC100EP16VT

Description

5V ECL Differential Receiver/Driver

Manufacturer

ON Semiconductor

Datasheet

1.MC100EP16VT.pdf (12 pages)

Current page: 1 of 12
Download datasheet (198Kb)

MC100EP16VT

3.3V / 5V ECL Differential

Receiver/Driver with

Variable Output Swing and

Internal Input Termination

Description

to the 100EP16 with input pins controlling the amplitude of the outputs

(pin 1) and providing an internal termination network (pin 4).

and is referenced to V

output amplitude) to V

externally supplied voltage equal to V

and Figure 3). A variable resistor between V

wiper driving V

application circuits and a V

are described in this data sheet. When left open, the V

internally pulled down to V

100% output amplitude.

line impedance environment, shown in Figure 1. For further reference,

see Application Note AND8020, Termination of ECL Logic Devices.

Input considerations are required for D and D under no signal conditions

to prevent instability.

Signal conditions to prevent instability.

Features

•

December, 2006 − Rev. 3

CTRL

The MC100EP16VT is a differential receiver functionally equivalent

The V

Special considerations are required for differential inputs under No

with V

220 ps Propagation Delay

Maximum Frequency > 4 GHz Typical (See Graph)

The 100 Series Contains Temperature Compensation

PECL Mode Operating Range: V

NECL Mode Operating Range: V

Open Input Default State

50 W Internal Termination Resistor

Pb−Free Packages are Available

input is from V

CTRL

input pin offers an internal termination network for a 50 W

= 0 V

= −3.0 V to −5.5 V

input pin controls the output amplitude of the EP16VT

CTRL

, can control the output amplitude. Typical

. (See Figure 4.) The operational range of the

CTRL

(minimum output amplitude). V

(a supply at V

and operate as a standard EP16, with

Voltage vs. Output Amplitude graph

= 3.0 V to 5.5 V

= 0 V

−1.42 V (See Figures 2

−1.42 V, maximum

and V

CTRL

www.DataSheet4U.com

pin will be

, with the

is an

See detailed ordering and shipping information in the package

dimensions section on page 9 of this data sheet.

*For additional marking information, refer to

(Note: Microdot may be in either location)

Application Note AND8002/D.

CASE 506AA

MN SUFFIX

CASE 948R

DT SUFFIX

CASE 751

D SUFFIX

TSSOP−8

SOIC−8

ORDERING INFORMATION

DFN8

http://onsemi.com

= Assembly Location

= Wafer Lot

= Year

= Work Week

= Date Code

= Pb−Free Package

MARKING DIAGRAMS*

Publication Order Number:

ALYWG

KEP63

ALYW

MC100EP16VT/D

KP63

Related parts for MC100EP16VT

MC100EP16VT Summary of contents

Page 1

... Receiver/Driver with Variable Output Swing and Internal Input Termination Description The MC100EP16VT is a differential receiver functionally equivalent to the 100EP16 with input pins controlling the amplitude of the outputs (pin 1) and providing an internal termination network (pin 4). The V input pin controls the output amplitude of the EP16VT ...

Page 2

V 1 CTRL Figure 1. 8−Lead Pinout (Top View) and Logic Diagram Table 2. ATTRIBUTES Internal Input Pulldown Resistor Internal Input Pullup Resistor ESD Protection Moisture Sensitivity, Indefinite Time ...

Page 3

Table 3. MAXIMUM RATINGS Symbol Parameter V PECL Mode Power Supply CC V NECL Mode Power Supply EE V PECL Mode Input Voltage I NECL Mode Input Voltage I Output Current out T Operating Temperature Range A T Storage Temperature ...

Page 4

Table 5. DC CHARACTERISTICS, PECL Symbol Characteristic I Power Supply Current EE V Output HIGH Voltage (Note > Output LOW Voltage (Max Swing) OL (Note 6) V VCC CTRL ...

Page 5

Table 6. DC CHARACTERISTICS, NECL Symbol Characteristic I Power Supply Current EE V Output HIGH Voltage (Note > CTRL V Output LOW Voltage (Max Swing) OL (Note 9) V CTRL VCC V CTRL V ...

Page 6

Figure Min Swing V OL 0.0 0.5 1.0 1.5 1. VOLTS (V) − V (pin #1) CC CTRL Max Swing 1.0 ...

Page 7

V + CTRL 1 V CTRL Figure 4. Voltage Source Implementation CTRL Figure ...

Page 8

V + CTRL 1 V CTRL 5.0 V 112 W 3 Figure 7. Alternate “Y” Termination Method, V 1000 900 800 2.00 ...

Page 9

... ORDERING INFORMATION Device MC100EP16VTD MC100EP16VTDG MC100EP16VTDR2 MC100EP16VTDR2G MC100EP16VTDT MC100EP16VTDTG MC100EP16VTDTR2 MC100EP16VTDTR2G MC100EP16VTMNR4 MC100EP16VTMNR4G †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Resource Reference of Application Notes AN1405/D AN1406/D ...

Page 10

... C SEATING PLANE −Z− 0.25 (0.010 *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. PACKAGE DIMENSIONS SOIC−8 NB CASE 751−07 ISSUE 0.10 (0.004) ...

Page 11

K 8x REF 0.10 (0.004) 0.15 (0.006 L −U− PIN 1 IDENT 0.15 (0.006 −V− C 0.10 (0.004) D −T− SEATING G PLANE PACKAGE DIMENSIONS TSSOP−8 ...

Page 12

... COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. MILLIMETERS DIM MIN MAX A 0.80 1.00 A1 0.00 0.05 A3 0.20 REF b 0.20 0.30 D 2.00 BSC D2 1.10 1.30 E 2.00 BSC E2 0.70 0.90 e 0.50 BSC K 0.20 −−− L 0.25 0.35 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC100EP16VT/D ...

Related keywords

MC100EP16VT datasheet
MC100EP16VT data sheet
MC100EP16VT pdf datasheet
MC100EP16VT component
MC100EP16VT part
MC100EP16VT distributor
MC100EP16VT RoHS
MC100EP16VT datasheet download