ATS616LSG Allegro MicroSystems, ATS616LSG Datasheet
ATS616LSG
Available stocks
Related parts for ATS616LSG
ATS616LSG Summary of contents
Page 1
... J(max) Storage Temperature, T .................. –65ºC to 170ºC S *See Power Derating section. ATS616LSG-DS, Rev. 1 ATS616LSG Hall Effect Gear Tooth Sensor The ATS616 gear-tooth sensor is a peak-detecting device that uses automatic gain control and an integrated capacitor to provide extremely accurate gear edge detec- tion down to low operating speeds. Each sensor module consists of a high-tem- ...
Page 2
... Dynamic Self-Calibrating Peak-Detecting Differential Hall Effect Gear Tooth Sensor www.datasheet4u.com VCC Voltage Regulator Hall Amp Hall Amp ATS616LSG-DS, Rev. 1 ATS616LSG Functional Block Diagram UVLO Tooth and Valley Comparator Gain Track and Hold Reference Generator Track and Hold GND (Recommended) Power-On Logic ...
Page 3
... Maximum voltage must be adjusted for power dissipation and junction temperature; see Power Derating section the probe capacitance of the oscilloscope used to make the measurement (millitesla), exactly. 5 Non-uniform magnetic profiles may require additional edges before calibration is complete. ATS616LSG-DS, Rev. 1 ATS616LSG Symbol Test Condition V Operating, T < 165° ...
Page 4
... Valley width, t > • Valley depth, h > • Tooth thickness, F ≥ • Target material must be low carbon steel ATS616LSG-DS, Rev. 1 ATS616LSG Reference Target (Gear) Information Test Conditions Typ. Outside diameter of target 120 Breadth of tooth, with respect 6 ...
Page 5
... T (°C) A Output Voltage (On) versus Ambient Temperature 350 300 250 200 150 100 50 0 – 100 T (°C) A Continued on the next page. ATS616LSG-DS, Rev. 1 ATS616LSG Characteristic Data (° – 150 ...
Page 6
... Dynamic Self-Calibrating Peak-Detecting Differential Hall Effect Gear Tooth Sensor www.datasheet4u.com Relative Timing Accuracy versus Air Gap Sequential Tooth Falling Edge 1000 rpm 1.5 1.0 0.5 0.0 -0.5 -1.0 -1.5 0 0.5 1.0 1.5 AG (mm) Relative Timing Accuracy versus Air Gap Signature Tooth Falling Edge 1000 rpm 1.5 1.0 0.5 0.0 -0.5 -1.0 -1.5 0 0.5 1.0 1.5 AG (mm) ATS616LSG-DS, Rev. 1 ATS616LSG Characteristic Data 1.5 1.0 T (°C) A 0.5 – -0.5 125 150 -1.0 -1.5 2.0 2.5 3.0 1.5 1.0 T (°C) A 0.5 – ...
Page 7
... T (°C) A Relative Timing Accuracy versus Ambient Temperature Sequential Tooth Rising Edge 0.5 mm 1.5 1.0 0.5 0.0 -0.5 -1.0 -1.5 – 100 T (°C) A ATS616LSG-DS, Rev. 1 ATS616LSG Characteristic Data (continued) Relative Timing Accuracy versus Ambient Temperature 1.5 1.0 rpm 0.5 10 100 0.0 500 1000 -0.5 1500 2000 -1.0 -1.5 150 200 –50 Relative Timing Accuracy versus Ambient Temperature 1 ...
Page 8
... Dynamic Self-Calibrating Peak-Detecting Differential Hall Effect Gear Tooth Sensor THERMAL CHARACTERISTICS may require derating at maximum conditions, see application information Characteristic www.datasheet4u.com Package Thermal Resistance *Additional information is available on the Allegro Web site. ATS616LSG-DS, Rev. 1 ATS616LSG Symbol Test Conditions* Single-sided PCB with copper limited to solder pads R Two-sided PCB with copper limited to solder pads and 3.57 in. θ ...
Page 9
... Hall Effect Device North Pole (Pin n >1 Side) Figure 2. Relative motion of the target is detected by the dual Hall ele- ments mounted on the Hall IC. ATS616LSG-DS, Rev. 1 ATS616LSG Functional Description rejection circuitry. The Hall transducers and signal processing electronics are integrated on the same silicon substrate, using a proprietary BiCMOS process ...
Page 10
... Immunity to gear run out. The differential sensor configura- tion eliminates the baseline variations caused by gear run out. Differential vs. Single-Element Sensing. Hall-effect configuration is superior in most applications to the ATS616LSG-DS, Rev. 1 ATS616LSG classical single-element gear-tooth sensor. The single-element configuration commonly used (Hall-effect sensor mounted on the face of a simple permanent magnet) requires the detection of a small signal (often < ...
Page 11
... OUT Target Motion from Pin 4 to Pin 1 Figure 7. The magnetic profile reflects the geometry of the target, allowing the device to present an accurate digital output response. ATS616LSG-DS, Rev. 1 ATS616LSG High-pass filtering is below the minimum operating voltage, V off and stays off, irrespective of the state of the magnetic field. ...
Page 12
... 140°C/W = 7°C θ ΔT = 25°C + 7°C = 32° ATS616LSG-DS, Rev. 1 ATS616LSG Power Derating A worst-case estimate, P able power level ( selected R Example: Reliability for V minimum-K PCB figure of merit sum- Observe the worst-case ratings for the device, specifically: θJA R θ ...
Page 13
... Temperature excursions 225°C for 2 minutes or less are permitted. b Industry accepted soldering techniques are acceptable for this package as long as the indicated maximum temperature is not exceeded. Additional soldering information is available on the Allegro Web site. ATS616LSG-DS, Rev. 1 ATS616LSG Characterization Only Test Name* ...
Page 14
... The in for ma tion in clud ed herein is believed rate and reliable. How ev er, Allegro MicroSystems, Inc. assumes no re spon si bil i ty for its use; nor for any in fringe ment of patents or other rights of third parties which may result from its use. Copyright © 2005 Allegro MicroSystems, Inc. ATS616LSG-DS, Rev. 1 ATS616LSG Package SG Module ...