UCC2830-4 Unitrode Semiconductor, UCC2830-4 Datasheet

no-image

UCC2830-4

Manufacturer Part Number
UCC2830-4
Description
5-Bit Microprocessor Power Supply Controller
Manufacturer
Unitrode Semiconductor
Datasheet
9/97
5-Bit Microprocessor Power Supply Controller
FEATURES
BLOCK DIAGRAM
5-Bit Digital-to-Analog
Converter (DAC)
Supports 4-Bit and 5-Bit
Microprocessor VID Codes
Combined DAC/Voltage
Monitor and PWM Functions
1% DAC/Reference
Current Sharing
100kHz, 200kHz, 400kHz
Oscillator Frequency Options
Foldback Current Limiting
Overvoltage and Undervoltage
Fault Windows
Undervoltage Lockout
4 Totem Pole Output
Chip Disable Function
DESCRIPTION
The UCC3830-4/-5/-6 is a fully integrated single chip solution ideal for power-
ing high performance microprocessors. The chip includes an average current
mode PWM controller, has a fully integrated 5-Bit DAC, and includes an on-
board precision reference and voltage monitor circuitry. The UCC3830-x con-
verts 5VDC to an adjustable output, ranging from 3.5VDC down to 1.8VDC
with 1% DC system accuracy (see Table 1). The UCC3830-x fully supports In-
tel’s 4-bit Pentium® Pro and 5-bit Pentium® II VID codes.
The accuracy of the DAC/reference combination is 1%. The overvoltage and
undervoltage comparators monitor the system output voltage and indicate
when it rises above or falls below its programmed value by more than 8.5%. A
second overvoltage protection comparator pulls the current amplifier output
voltage low to force zero duty cycle when the system output voltage exceeds
its designed value by more than 17.5%. This comparator also terminates the
cycle. Undervoltage lockout circuitry assures the correct logic states at the out-
puts during powerup and powerdown. The gate output can be disabled by
bringing the CAO/ENBL pin to below 0.8V.
The voltage and current amplifiers have a 3MHz gain bandwidth product to sat-
isfy high performance system requirements. The internal current sense ampli-
fier permits the use of a low value current sense resistor, minimizing power
loss. The oscillator frequency is fixed internally at 100kHz, 200kHz, or 400kHz,
UCC2830-4/-5/-6
UCC3830-4/-5/-6
(continued)
UDG-96188-2

Related parts for UCC2830-4

UCC2830-4 Summary of contents

Page 1

... The voltage and current amplifiers have a 3MHz gain bandwidth product to sat- isfy high performance system requirements. The internal current sense ampli- fier permits the use of a low value current sense resistor, minimizing power loss. The oscillator frequency is fixed internally at 100kHz, 200kHz, or 400kHz, UCC2830-4/-5/-6 UCC3830-4/-5/-6 (continued) UDG-96188-2 ...

Page 2

... VIN < 13.2V 0mA, 0°C < T VREF 10.8V < VIN < 13.2V 0mA, –25°C < T VREF DX Pin Floating DX Pin Tied to GND % Over COMMAND Voltage (Note 1 Open GND OV, OVP, UV Combined 2 UCC2830-4/-5/-6 UCC3830-4/-5/-6 Frequency Table Frequency 100kHz 200kHz 400kHz X X MIN TYP MAX UNITS 10 ...

Page 3

... CAM CAO/ENBL COMP 10.8V < VIN < 15V I = –100mA GATE I = 100mA GATE C = 3.3nF GATE C = 3.3nF GATE Measured at Voltage EA Output SENSE COMMAND COMMAND SENSE 3 UCC2830-4/-5/-6 UCC3830-4/-5/-6 MIN TYP MAX UNITS 5 8 470 –12 –8.5 – –0.5 –0.02 0 –0.5 – ...

Page 4

... VREF powers the D/A converter and also provides a threshold voltage for the UVLO comparator. For best reference stability, bypass VREF directly to GND with a low ESR, low ESL capacitor of at least 0. UCC2830-4/-5/-6 UCC3830-4/-5/- where CSA ...

Page 5

... Enabling/Disabling the UCC3830-x Gate Drive The CAO/ENBL pin can be used to disable the UCC3830 gate drive by forcing this pin below 0.8V, as shown in Figure 4. Bringing the voltage below the valley of the PWM oscillator ramp will insure a 0% duty cycle, effec- 5 UCC2830-4/-5/-6 UCC3830-4/-5/-6 1000000 10000000 100000000 FREQUENCY [Hz] ...

Page 6

... Enabled Enabled Enabled Enabled Enabled Enabled UCC2830-4/-5/-6 UCC3830-4/-5/-6 Command GATEHI/GATELO D0 Voltage Status 1 2.000 Note 1 0 2.100 Enabled 1 2.200 Enabled 0 2.300 Enabled 1 2.400 Enabled 0 2.500 Enabled 1 2.600 Enabled 0 2.700 Enabled 1 2 ...

Page 7

... UCC3830-x when the Pentium® Pro requires lower bus voltages. 5V, 2. UCC2830-4/-5/-6 UCC3830-4/-5/- LOAD CURRENT [A] Figure 7. Efficiency of UCC3830-5 200kHz Demo Kit at 2.8V Ouput 14 16 UDG-96190-1 ...

Page 8

... Radial Can 10x20mm Radial Can 10x20mm Radial Can 10x20mm Radial Can 10x20mm Radial Can 10x20mm Radial Can 10x20mm Radial Can SMD Power Package 8 UCC2830-4/-5/-6 UCC3830-4/-5/-6 PACKAGE SOIC-20 Wide SPRAGUE Size A EIA Size D SMD 1206 SMD 0603 SMD 0603 SMD 0603 SMD ...

Related keywords